pitt_md
Veteran Member
I have been considering getting a snowblower and found a Erskine brand 3pt that is pulled forward to use. Anyone have experience/opinions on this brand/model?
Snow Attachments erskine Rear Pull Snow blower?
- Thread starter pitt_md
- Start date
- Views: 3713
lungdoc
Gold Member
If you search around there are threads on these, I know as I had strongly considered. Nobody has anything bad to say about Erskine products or company AFAIK. The rear pull models have a strong appeal - less neck turning and drive away from the plume of snow. I ended up going conventional mainly for cost and for clean-up work after truck-mounted plowing (to remove banks) where I thought rear-facing would be easier to lift up and back into a bank. Those who have them seem to love them and the often-noted issue of packing snow with wheels first isn't an issue - blower still cleans down to the scraper set level. Can be an issue is huge dump or drifts or plowed mounds/banks as have to go through first but presumably still have an FEL.
Thumper & Buttercup
Gold Member
Hey pitt_md,
I've got one of the older ones on the farm. I tried to use it behind a 9N tractor but without live pto it did not work so good. We are west of Grand Forks ND and you are more than welcome to this one I have. It's a 5', it needs a spring to put tension on the divert-er for the chute but other than that it's ok.
Hope this helps.
I've got one of the older ones on the farm. I tried to use it behind a 9N tractor but without live pto it did not work so good. We are west of Grand Forks ND and you are more than welcome to this one I have. It's a 5', it needs a spring to put tension on the divert-er for the chute but other than that it's ok.
Hope this helps.
OP
pitt_md
Veteran Member
Thanks for the offer. I am looking for something a little bigger though. 6' - 7' would be good.
Thumper & Buttercup
Gold Member
I'm pretty sure it's about 5', it was the same width of
a 9N. I think you would be happier with a backup blower
than the pull type. Or a front mount if you can find one.
a 9N. I think you would be happier with a backup blower
than the pull type. Or a front mount if you can find one.
skidsteer.ca
Gold Member
Would be happy to help you with either a rear pull or front mount.
pm me.
Ken
pm me.
Ken
crk133
Silver Member
i have a new erskine 78" rear pull, hyd chute and deflector. works fine could throw the snow further is my only complaint so far. i have pulled it through 2' drifts with no issues just havew to slow down so it doesnt clog up. pm me if you have any more questions
hanson1999
Gold Member
thumper, any pics of the blower and what do u want for it? i live between fargo and forks and would be interested in that type of blower.
thanks!
thanks!
Thumper & Buttercup
Gold Member
Hey hanson1999,
I'll give it to you just come over and get it
).
IM for contact info.
Mark
I'll give it to you just come over and get it
).IM for contact info.
Mark
wildwillie
Silver Member
I just ordered an erskine rear pull for my L3400, no mid pto for this model.
Should have it in a couple of weeks. I do over a mile of road and would not even consider a rear push. I got tired of tearing up trucks with plows , not so much the dirt road but me beating on the trucks. I will do a post when it's up and running.
Should have it in a couple of weeks. I do over a mile of road and would not even consider a rear push. I got tired of tearing up trucks with plows , not so much the dirt road but me beating on the trucks. I will do a post when it's up and running.