question about hydraulic valves

   / question about hydraulic valves #11  
WilcoKubota; said:
Its for a FEL, so only if they have a PB port i can connect it like this:

Wilco.

Look at the schematic at the bottom. The flow has to go through the valve and then go to another valve IN port.

http://www.surpluscenter.com/Instruct/I9- 7863.pdf

Do you need float or regen?
 
   / question about hydraulic valves
  • Thread Starter
#12  
I don't get it very much, but i've seen the prices of a single spool valve with PB port, and i can better buy a 3 spool valve because that is cheaper.

Thank you for the help anyway.

Wilco.
 
   / question about hydraulic valves #13  
That is fine, but if you have a 3pt on the tractor, you will need PB on that three spool valve.

If that is the only valve you will use, it does not have to be PB.
 
   / question about hydraulic valves #15  
Yes, that is your supply for the 3pt valve and the 3pt dumps to tank. The OUT port of the FEL valve should go to tank.

Do you need any more hyd for the rear such as a remote valve for implements, etc?
 
   / question about hydraulic valves
  • Thread Starter
#16  
Yes, that is your supply for the 3pt valve and the 3pt dumps to tank. The OUT port of the FEL valve should go to tank.

Ok. I understand.

Do you need any more hyd for the rear such as a remote valve for implements, etc?

I already have one double action valve at the back. i think I've got a picture of it..
you can see it between the wheel and the top link, at the 1th picture.

I want to make the valve above the brake shield (I don't know the correct name.), at the 2nd picture.

Wilco
 

Attachments

  • img1147237937.jpeg
    img1147237937.jpeg
    177.5 KB · Views: 204
  • img1147236187.jpeg
    img1147236187.jpeg
    181.6 KB · Views: 162
   / question about hydraulic valves #17  
Can you provide a description of the hyd flow as it is now.

A basic tractor comes with a 3pt, so the pump flow only goes to the 3pt. It may do this through a hyd block at the middle of the tractor, or direct. You may also have a switch to switch the flow from 3pt to something else.

You said something about a valve. I only see two lines that are capped. Is there a valve for those lines?

I have a Kubota B9200 HST, and the pump flow goes through a hyd block and to the 3pt in one position of a switch, and if I switch the flow, it goes to a rear remote first and then to the 3pt. If I am not using the rear remote, I plug the two hoses together.
 
   / question about hydraulic valves
  • Thread Starter
#18  
No, its a built in valve, the lines at the picture are to a quick male connector. I'ts an old picture because i have now female connectors on it.

Wilco
 
   / question about hydraulic valves #19  
We were talking about the rubber pipe going to the left from the hydro cylinder area just under the seat.
 

Attachments

  • KL2202 Atvaizd0098.jpg
    KL2202 Atvaizd0098.jpg
    90.6 KB · Views: 155
   / question about hydraulic valves
  • Thread Starter
#20  
I have it this way:

Wilco
 

Attachments

  • dv1.jpg
    dv1.jpg
    170.6 KB · Views: 176
  • dv2.jpg
    dv2.jpg
    147.3 KB · Views: 159
  • dv3.jpg
    dv3.jpg
    174 KB · Views: 153

Tractor & Equipment Auctions

2013 Ford F-150 Ext. Cab Pickup Truck (A50323)
2013 Ford F-150...
AFE SSMM Disc Mulcher Skid Steer Attachment (A49461)
AFE SSMM Disc...
TAKEUCHI TB210R EXCAVATOR (A51242)
TAKEUCHI TB210R...
2016 Big Tex 14LX 14ft 7 Ton T/A Dump Trailer (A50322)
2016 Big Tex 14LX...
2003 Big Tex 10PI 16ft. T/A Pipe Top Utility Trailer (A49461)
2003 Big Tex 10PI...
2006 CHEVROLET EXPRESS SERVICE VAN (A51219)
2006 CHEVROLET...
 
Top