YM336D - Started knocking loud while tilling
- Thread starter Domush
- Start date
- Views: 87987
Pete Judd
Veteran Member
- Joined
- Aug 18, 2010
- Messages
- 1,013
- Location
- The Thin Gravy Ranch in The wet PNW
- Tractor
- Yanmar 186d, JD 314
Manual42, do you own a tractor, or are you only in the marketing of manuals?
Looks like your postings would fall under "spam"
Looks like your postings would fall under "spam"
grainger12002
Platinum Member
- Joined
- Oct 1, 2002
- Messages
- 806
- Location
- Pomfret,Connecticut
- Tractor
- yanmar 336d w ldr,Cub,many attachments
doesn't look like much good reading as there is no english printed there..........
OP
Domush
Platinum Member
Thanks for all of the compliments. I'm glad this thread is helpful to people.
I'm a learning ***** and this project, and the people helping me, satisfied my learning needs nicely. I hope this thread can serve as an example for others to share their projects and experiences.
I look forward to following your restoration, MasseyWV
I'm a learning ***** and this project, and the people helping me, satisfied my learning needs nicely. I hope this thread can serve as an example for others to share their projects and experiences.
I look forward to following your restoration, MasseyWV
ChiefLoneWolf
Silver Member
Wow, Domush, this is amazing. What a fine job you did. I envy you for your skills, patience and perseverance. I am not clumsy-handed either, but much lacking the persistence in following through :ashamed: besides the fact that I don't (yet) have a decent workshop (working on it).
Congratulations :thumbsup::thumbsup::thumbsup:.
Congratulations :thumbsup::thumbsup::thumbsup:.
clemsonfor
Super Member
Neither did Domush, he did that in his yard!!
OP
Domush
Platinum Member
Hey everyone! It has been a while since the rebuild was completed. I have put about 7 hours on the tractor since then and given it the first post-rebuild oil change, so I wanted to let everyone know how things are going.
I made a quick video with the engine running and exhaust at rev so everyone can hear what it sounds like after some break-in time. I've used it to do some bush hogging, finish mowing and even used the boom pole to lift a FEL into a trailer, which was slightly more than the boom pole was rated for. I got the feeling my tractor was less than happy about lifting that weight, as the hydraulic relief valve was squealing away the whole time as well, haha! So, needless to say it has been fully broken in. One note on the oil change, the oil came out crystal clear, not even a hint of darkness to it. So, it appears even a diesel can run crisp and clean. I hated wasting $30 in 5 hour old oil, but I guess that's just the final cost in engine rebuilds.
I haven't fixed the 1st or 2nd gears yet, but so far I haven't needed to. I did install some rear facing lights on the canopy in order to make using the boom pole at night easier. I notice the alternator is a little tired, as it only puts out 13.5v at high idle and 12.8 at 1,000rpm. A new one will be in my future at some point. No rush until it stops charging entirely.
On a side note, I certainly love the fact it can idle at 1,000rpm, now. It could never do that before the rebuild. Saves on fuel and my eardrums (though I never use it without earmuffs).
Without further ado (best played in full-screen 720p)..
Post engine rebuild - Yanmar YM336D - Sound and exhaust - YouTube
I made a quick video with the engine running and exhaust at rev so everyone can hear what it sounds like after some break-in time. I've used it to do some bush hogging, finish mowing and even used the boom pole to lift a FEL into a trailer, which was slightly more than the boom pole was rated for. I got the feeling my tractor was less than happy about lifting that weight, as the hydraulic relief valve was squealing away the whole time as well, haha! So, needless to say it has been fully broken in. One note on the oil change, the oil came out crystal clear, not even a hint of darkness to it. So, it appears even a diesel can run crisp and clean. I hated wasting $30 in 5 hour old oil, but I guess that's just the final cost in engine rebuilds.
I haven't fixed the 1st or 2nd gears yet, but so far I haven't needed to. I did install some rear facing lights on the canopy in order to make using the boom pole at night easier. I notice the alternator is a little tired, as it only puts out 13.5v at high idle and 12.8 at 1,000rpm. A new one will be in my future at some point. No rush until it stops charging entirely.
On a side note, I certainly love the fact it can idle at 1,000rpm, now. It could never do that before the rebuild. Saves on fuel and my eardrums (though I never use it without earmuffs).
Without further ado (best played in full-screen 720p)..
Post engine rebuild - Yanmar YM336D - Sound and exhaust - YouTube
Thanks for another good video. Purring like a kitten! Watching the voltmeter it looks like your regulator might be what is cutting the charge back. Might try putting your hand voltmeter on the alternator and see what it is putting out at fast idle. Just a thought.
