Box Scraper Gannon 8' blade

[Turbys_1700]

Nothing more really for me to say except buy it. I doubt that it will be available very long at that price. Heck of a bargain.

 

[coolnature]

I would drop whatever I was doing and go get it. I priced a new 92" wide model with the pin kit and hoses -$3,500.00 I would love to have it behind my T4.95.

 

[Degolyerent]

I went to look at the blade today and it was not good, at all. The fella that had it runs an asphalt resurfacing company and that is why it has the add on skids on each side. The inside moldboard which you can't see in the picture is a mess as it is almost completely gone on the bottom with no blade remaining on the inside whatsoever, and the mounting holes are gone because of the wear. I offered him scrap metal price which he turned down. Way to much repair needed on it to pay more than that in my opinion, especially since it is not a perfect fit anyway. Thanks for the input and information everyone!
John

 

[Ford850]

That's too bad. You did make me curious enough to search "gannon" on craigslist in hopes of finding something good. I found a little 4' blade with hydraulic scarifiers listed for $650. It's shown here in case anyone needs a smaller one. Gannon 48" Box Blade Scraper for 3 Point Tractor

 

[Poopdeck Pappy]

That's too bad. You did make me curious enough to search "gannon" on craigslist in hopes of finding something good. I found a little 4' blade with hydraulic scarifiers listed for $650. It's shown here in case anyone needs a smaller one. Gannon 48" Box Blade Scraper for 3 Point Tractor

I'd buy that little bugger for my BX2660 if it was local. I've never seen a 4-footer with hydraulic scarifiers.

 

[C4Ranch]

I'd buy it. If it'll help, here is my review of a 2014 Frontier version of that Gannon. The only real differences are the Frontier is both CAT 1 and Cat 2 quick hitch compatible, and the Frontier has an adjustable rear tailgate. I didn't get into the tailgate in the video, but the folding tailgate allows the box to sink in faster and take out more material in a shorter space before filling up.

FWIW, since I shopped this in the last 12 months, the blade you're looking at new is about $3400-3800.

Wow Eric, I can't believe those shanks bent. Think they're the same material as Gannon? I never would have imagined mine bending. Heavy chunk of steel..

 

[ovrszd]

I was reading down thru this thread toward the end so I could post that it doesn't look like a bargain to me. Then I got to your post where you had went to look at it. You are a generous man to offer scrap price. You are also a wise man to not jump in with money before looking it over good. Pictures on Craigslist or wherever rarely tell the whole story.

 

[MinnesotaEric]

Wow Eric, I can't believe those shanks bent. Think they're the same material as Gannon? I never would have imagined mine bending. Heavy chunk of steel..

I'd need a direct side by comparison to know if the Frontier scarifiers are the same.

Next time I spend quality time with my tractor, I'll try to remember to take a photo of a straight scarifier and take down the measurements and add what I find on the thread I started about hydraulic box blade designs. It would be nice to know if the Frontier can use the Gannon scarifiers and help identify if Frontier is making their own thing, or if Woods/Gannon is making the Frontier commercial box scrapers.

 

[ecuffee2]

I'd go for it , picked up my used 76" Gannon missing rippers and the hydraulic cylinder , i was able to use it on my Ford 3000 without to much trouble- although a lite touch helps.

what is the hydraulic cylinder part number and make Thank you

 

[sd455dan]

what is the hydraulic cylinder part number and make Thank you

Don't know- I have been using it as is, Still don't have scarifiers or the hydraulic cylinder.

If the need to do scarifier/ripper work arises I use the dozers rippers




As to the part # of the cylinder I do recall someone who was looking into a replacement- but can't seem to find where it was mentioned on TBN... Sorry