Recent content by ch47dpilot

I've had good luck with king kutter products. Don't have they're tiller but other items. Rural King sells them. American made in Alabama

Don't want to change topic but has anyone used DR pull behind mower. I have an area near a pond where my tractor will sometimes get stuck in softer ground. Was thinking the pull behind would be great since my 4-wheeler wouldn't get stuck as easily

Just bought 2 Carlisle from Amazon for L3400. They seem to be good quality and stapped MADE IN USA

I found the cab to an old Ford pickup. Not sure about year figuring late 50 early 60s. First it was just the steering box I hit. Started digging and pulling and can across complete cab

Got most of my 3rd function and rear hydraulics plumbed and working. Only need to make brackets for the Quick Disconnects. I used as much of the original plumbing to reduce cost. The original PWR Beyond hose from FEL became the PB for the new valve and a new hose runs from the FEL to new rear...

I'm in the process of building a monitor style barn. The first picture is exactly what I'm looking at other than size. The barn's center section will be 16'x36', post 12' apart. The center post will be 20' 8x8 treated, 4' in ground 16' high. I'm trying to figure out the best way to install a...

Looking at a backhoe for my tractor. I'm very familiar with the hydraulic system as far as power beyond, closed vs open circuits ect. I've noticed most of the backhoes have only 2 hoses. Power and return. Right now my hydraulics go FEL--PWR beyond to 3 point---to tank. The FEL has its own...

Have an older KingKutter post hole digger. Would like to convert to hydraulic drive. I've heard the ability to reverse comes in handy. Anybody attempted this and any opinion. My main concern is will my Kubota L3400 at 6.8 gal/min and about 2500PSI work. Also the best way to mount the motor...

I have the TS version of Pats Easy Change System. The adapter is designed for CAT 2 but my attachments are CAT1. I found these on Amazon. Amazon.com: RanchEx 1274 Quick Hitch Adapter Bushing Kit - Cat 1 For Quick Hitch (SKU 12851): Garden & Outdoor based on the description I figured they...

Seen two types of hot water pressure washers. Ones with steam, temp about 250F. The others are just hot water, temp around 200F. Anyone use both types and have an opinion on if the steam ones are really worth getting over just really hot water ones.

Not sure if this is the right forum, if not please let me know what would be a better place. I'm wondering if anyone has built a DIY oil water separator for a garage drain. My garage drains are just going to gravity feed through pipe away from garage. I'd like to "clean" the water, if...

My house has a septic tank and drain field but my workshop is to far away and uphill to make connecting into the system practical. I'm contemplating a separate septic/drain field for my workshop but may just go with a holding tank. My concern with the holding tank is how often I may need to...

Can anyone tell me why my CAT 1 attachments lower link points are different dimensions. I have a King Kutter 5' rotary cutter, 6' finish mower and 6' Blade. Also have a 5' box blade and 6' yard rake from other companies. The inside pin dimensions vary from approximately 24" to as much as 27"...

Got a few 55 gallon drums laying around and found a guy who can get them for $5. Going to make a burn barrel out of one and was thinking about a lawn roller for another. Would be interested in seeing other things people made out of these drums

I'm building a work shop and planning on 200amp service but not sure if that's enough. I plan to have a welder (50A), compressor (50A) and plasma cutter (50A). All could be on at same time possibly. Then there would be the normal lights, fans ect you'd be using in a shop and possibly a window...