Cycledude's latest activity

  • Cycledude
    Cycledude reacted to 2manyrocks's post in the thread Not to Brag, but... with Good Post Good Post.
    I use a drill rod that is about 5 feet long as a lever to move my brush cutter into final position for hookup to the 3pt hitch. Parking...
  • Cycledude
    Cycledude reacted to TractorGunn's post in the thread Not to Brag, but... with Good Post Good Post.
    It wasn't a race, it just went really smooth. Um...ya think? Do you know the difference between a tractor and a plane? :unsure:
  • Cycledude
    Cycledude reacted to TractorGunn's post in the thread Not to Brag, but... with Good Post Good Post.
    No dolly for mine. Can you post a picture?
  • Cycledude
    Cycledude reacted to HAR's post in the thread Not to Brag, but... with Good Post Good Post.
    Hmmmm....I never thought that hitching up a tool to another tool was a race against time. Taking the time to make sure that everything...
  • Cycledude
    Cycledude reacted to Little Red Tractor's post in the thread Not to Brag, but... with Good Post Good Post.
    I have found that if I lube the splines on the PTO shaft, as well as the shaft locking component--be it a collet or a pin-locking...
  • Cycledude
    Cycledude reacted to Bill601's post in the thread Not to Brag, but... with Good Post Good Post.
    Congratulations! Do you have it on a dolly? I made one for mine and it's made connecting it much faster and easier. It's easier to...
  • Cycledude
    Cycledude reacted to AlbionWood's post in the thread Injector problem or something else? with Good Post Good Post.
    You were on the right track - I put in a fuel pump between the filter and the injection pump and that fixed it! A friend who is a diesel...
  • Cycledude
    Cycledude reacted to AlbionWood's post in the thread Injector problem or something else? with Good Post Good Post.
    No, the injection pump is unaffected by inlet pressure. What was happening was it couldn't get enough fuel flow at the higher rpm...
  • Cycledude
    Cycledude replied to the thread R4 Tire Pressure.
    Sure is strange that LS didn’t put some kind of recommendations for tire air pressure in the owners manual. No pressure indicated on my...
  • Cycledude
    Cycledude reacted to Texasmark's post in the thread R4 Tire Pressure with Good Post Good Post.
    For a softer ride I adjust tire pressure to the point where the tires bulge slightly with the maximum load they encounter. R4s have a...
  • Cycledude
    Cycledude reacted to Avenger's post in the thread R4 Tire Pressure with Good Post Good Post.
    That actually happened to me this last fall when I dumped the air out of rear tires for snow chain install. I jacked the rear of the...
  • Cycledude
    Cycledude reacted to PeteN's post in the thread R4 Tire Pressure with Good Post Good Post.
    Dealer set the pressures quite high and not evenly. Had 36psi in the fronts and the rears were 21psi on the left side and 24 psi on the...
  • Cycledude
    Cycledude reacted to dieselscout80's post in the thread R4 Tire Pressure with Good Post Good Post.
    On my NH TC45 I have 16 psi in the fronts 10x16.5 and 12 psi in the 17.5x24 rear tires. To get full contact with the rears I need to go...
  • Cycledude
    Cycledude reacted to jigs_n_fixtures's post in the thread R4 Tire Pressure with Good Post Good Post.
    Get one of the laser aimed thermometer. Run the tractor around a bit, and then take three reading on the tire surface or lugs. The...
  • Cycledude
    Cycledude reacted to PeteN's post in the thread R4 Tire Pressure with Good Post Good Post.
    I've looked through the owner's manual for my MT357HC to find nominal tire pressures for the R4's I have on this tractor. Nothing...
Show older items

Footer Links 1

Top