I have for a couple of years had a front snowblower for my bx2360. In the past my driveway was paved and even with the little spacers set to their highest setting it would scrape the pavement bare when I used it. Now I have a gravel driveway, and it slopes up quite a bit about 15 feet from the...
I just tried my blower out on the bx2360 today (the kubota front blower). It worked great but at the end it clogged with slush and I had to jam a hockey stick into it for like 10 minutes to get it cleared out so it would blow again. I know the snow is very wet today as there was only maybe 3...
I have had a few issues, being this is my first tractor I am not sure if they are normal or not. First when I got my mower deck the grease fitting on the balance shaft would not accept grease. Then I went to grease my snow blower PTO and one of the fittings was stripped and pulled right out in...
I have a BX2751 quick hitch and a BX2753 mid pto kit for my BX2360 tractor. The manual though is for the shorter BX2752 which is the shorter pto kit for the BX1860 and so it says to set the shaft sticking back 5" from the hitch. I am just wondering how far back the BX2753 shaft is supposed to...
I have a bx2360. Using it to plow snow and sometimes it just starts slipping due to lack of traction. Sometimes I make passes with the diff lock engaged so that it makes it through a bit better. Definately the tires are able to slip if needed but sometimes I smell a bit of a smell, not sure...
Ok I have a BX2360 and I have been using the loader and a box scraper to clear snow on my driveway. Its around 600 feet and is flat. I can do it in low but high gear makes it go so much faster. Sometimes though I can hear it struggling in high gear, is this bad for the HST or is it ok to bog...
I am on tirechains.com as I have noticed others have bought chains there for their BXs. I know my R4s are 26x12x12 on the rear but I see there are two options for chains, medium duty and heavy duty. Which ones have you guys been buying? If medium duty will do the job then I will save the cash...
The stabilizers on the 3pt hitch suck on the BX 2360...what a huge pain you basically need a wrench to tighten them and it takes forever. Is there any way to put something better on this tractor? I am considering having wing nuts welded onto the threaded portion so at least I can turn it...
I bought a BX2360 in the spring, I got a ballast box with it which I haven't used because I used my box scraper as ballast. I decided I wanted to use the box as its less bulky and I hooked it up to the tractor, only problem is that I don't think its the correct one for the tractor. The model...
I want to do this myself not go to the dealer. I plan to put antifreeze in the tires of my tractor, I can get it for $3 for 4 gallons so I figure this is likely the cheapest way to do it. I plan to ballast the the tires in my BX2360 but I have a few questions
1) How do I get it in there?
2)...
I have a BX2360. When I try to dig anything with it I feel as though there isn't enough weight to provide adequate traction. I have a box scraper on the back for ballast and the front of the tractor lifts easily without really doing much digging in to the hard clay around here. I figure...
I live in canada, niagara falls Ontario more specifically. It gets cold here in the winter obviously and I was wondering if there is anything I need to do to my tractor for the winter. I have heard the fuel could gel but I have no idea why they would sell such a fuel in Canada or what I need to...
So I have a 60" deck and I was cutting the grass and hit a bit of a rock, looking at the blade it looked ok except the tip was dinged and chipped a bit on one blade. I decided to take it off and take it to my dealer to have them look at it because I didn't know if I could grind it down or if I...
Just wondering how normal this is. I have 30 hours on my 2360 and decided to check the fluid levels today and noticed that the front axle oil isn't even on the dip stick. I can see there is oil down there but it doesn't reach the stick. I have to assume that it hasn't leaked out in 30 hours...
I have only had my tractor for a couple weeks and I noticed that the deck wouldn't lock in the TOP position. I looked around and noticed that the linkage that goes to the back of the tractor and has a bolt that you adjust to stop how far back the linkage can slide was broken. The end of it was...