Recent content by okie350

I posted a while back about my hydraulic lever not returning back to center when I am using it and lugging the engine untill I return it manually to center. As this seemed to be an intermintent problem I was not overly concerned with it. Things have changed. It is now raising part way, then...

The hydraulic lever on the BX2200 will not return to center. If I lower the mower deck to the set mowing height the lever will stay down. When rasing it will stay in the up position and you can hear the sound you hear when the pump has reached its limit. I have to manually return the lever to...

Has anyone built there own canopy for their tractor? would you share how you installed it and maybe share a few pics? I was given a used golf cart canopy and want to mount it on my L3010 and am looking for some installation ideas:thumbsup: Thanks

Has anyone located a source other than the dealer for a mower belt for a RCK-60B-22BX deck that goes on a BX 2200? the $123.00 price at the dealer is a little hard to swallow:( I was expecting $50 - $60 price range, however I am not having much luck locating one on the net. Do any of you have a...

There is a small allen set screw on the bottom of the transmission. This screw seems to have a small hole drilled in it. I do not know if it is supposed to have this hole or not. But it is weeping what apprears to be hydraulic oil, not much, but will leave a quarter size stain on the shop floor...

When going from reverse to forward direction i have noticed my little Bota seems to "bounce" two or three times before levealing out and roaring off. It only seems to do it if I only PARTIALLY push the peddle (like half way push it down) If I push all the way it does not seem to do it. Is this...

I was given a canopy of of an EZ GO golf cart, I want to mount this on my L3010. I am looking for mounting ideas, and was hoping someone on here has done this before so I can steal thier Idea:D Some Pictures would be great:thumbsup:

was given a 5 foot box blade and (i think) 6 ripper teeth. I do not know who makes the box blade but it does say Ford in big letters on the side. My question is how do the teeth stay in? It has notches in the teeth and it looks like you slide them in the support / holder and choose the depth...

BX2200 will run fine for a couple of hours and then will start lossing power and start sputtering and shaking, i will idle it down and let it "catch up" and it will regain all its power and then do it again in a few minutes. I changed both fuel filters, and added some seafoam to the fuel in...

The original battery finally died on the little Bota, after 8 years. so i need a new one. but the battery does not have any markings on it for me to tell how many cranking amps etc. anyone know what decent (not to expenseive) one to get

During our latest snow and Ice storms people were buying generators incase the power went out ( it did not in this area) I was told by a home depot employee that you can shut off the master switch at the breaker box and plug you generator into a wall receptical and back feed into your house to...

What would cause my loader to be jerky ( kind of bounces up and down while using it) would changing the fluid help?

I have been trying to post some chain link fencing for sale on Craigs list. the add was posted for a day and a half with no problems and lots of replys. Then suddenly I was red flagged and my post was removed. So I reposted, and an hour later I was flagged again. This is not the first time this...

BX2200 with 60 " mower deck. will raise to the #4 position but will not lock in the "top" position, this just started yesterday. I can get it to lock IF I pick up on the deck while operating the hydraulics. is there an adjustment or could something have broken? it raises fine just wont go to...

The support bracket that holds the gear box on the mid mount mower cracked and broke where the bolt holes are, and i need to replace it (left side as your sitting on it) I have two questions; 1) isn't this a kind of a strange piece to have break? I ordered a replacement ($49), kind of...