Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Classifieds
Auctions
Database
Quick Review
Quick Owner-Page
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
oldnslo's latest activity
O
oldnslo
replied to the thread
3 point hitch w/weight lock up
.
The three point valve is used to control the height or position of the three point arms similar to how the loader valve is used to...
15 minutes ago
O
oldnslo
replied to the thread
2018 Toolcat 5600 2100 hours charge pressure dropping when warming up !
.
It sounds like you have a bad hydrostatic pump or drive motor or possibly both since frequently when one component fails it contaminates...
45 minutes ago
O
oldnslo
replied to the thread
Ferris 810cc 26HP Vanguard Battery Constantly Dying?
.
what voltage do you see when engine is running at 3/4 to full throttle? What you are describing almost sounds like voltage regulator...
Yesterday at 10:20 PM
O
oldnslo
replied to the thread
Scag tiger cub running rough
.
If my memory is correct there was more than one option on how the choke and throttle were integrated. Can you see what activates the...
Yesterday at 10:15 PM
O
oldnslo
replied to the thread
I'll just have water
.
My wife and I will frequently split a meal if at a restaurant and bring leftovers home for another meal or two. I have never liked...
Yesterday at 1:53 PM
O
oldnslo
replied to the thread
Scag tiger cub running rough
.
There might or should be adjustment on when the throttle engages the choke. You want engine at full RPM before choke is engaged. Some...
Yesterday at 1:50 PM
O
oldnslo
reacted to
Alan W.'s post
in the thread
I'll just have water
with
Good Post
.
What you are calling a habit, some of us call a lifestyle. Everything is paid off and can buy what we want. But by todays standards we...
Yesterday at 1:08 PM
O
oldnslo
replied to the thread
Grease - is there no better way? Can we talk about this?
.
If my hands are greasy I just pick up a handful of dry dirt and scrub them like washing my hands. The dirt absorbs the grease and the...
Yesterday at 1:07 PM
O
oldnslo
replied to the thread
Mounting a Tilt Dump MCS on a JD445
.
Your 445 should handle that but like big tiller states you may need some front weights when that bagger is full of wet grass or support...
Yesterday at 1:02 PM
O
oldnslo
replied to the thread
Erratic and jerky hydraulics
.
Suction side with hose clamps is where air can be drawn in. Check to see if the hose has hardened or cracked with age. Also check to see...
Yesterday at 7:02 AM
O
oldnslo
replied to the thread
Hydraulic filter and cooler placement
.
The tank line is not gravity feed. In designing the filter and cooler circuit you want components that will handle the maximum return...
Yesterday at 6:58 AM
O
oldnslo
replied to the thread
Erratic and jerky hydraulics
.
Triple check all of connections on the inlet line to the pump to confirm they are tight and not leaking any air when under vacuum. If...
Sunday at 7:20 PM
O
oldnslo
reacted to
BeezFun's post
in the thread
Inserting new seal in single acting cylinder
with
Good Post
.
Thanks for the ideas. I do have a piston ring compressor but it's too big. I ended up cutting some thin shim stock and using it like an...
Sunday at 3:25 PM
O
oldnslo
replied to the thread
Hydraulic (flexwing mower) question...
.
Item 8 is required for the motor to operate correctly. It appears to be the seals for the pressure side load feature on the motor. High...
Sunday at 10:12 AM
O
oldnslo
replied to the thread
Diverter Valve Troubles
.
I would confirm that your loader valve has regen feature before changing anything. First would try pushing joystick farther to right...
Saturday at 10:00 PM
Forums
Top