Recent content by scooter133

I have the Parts, manual and service guides for the tractor. Thank you. I do need a new Dash housing, Turn Signal Switch and Headlight Switch. I have not dove into those 2 switches yet. I am open to non OEM types. Though I looked the Hole for the Horn button is about 7-8mm. That Horn button...

No, it’s not new. I think I got it in 2006? I’ve not been kind to it, so now I’m trying to go though some things and get her cleaned up.

I edited the Question, but the bulbs say NSN 12V 3.4W, HONDA OEM BULB 12V 3.4W) | 34902-259-003 With a BA9S base. The apparent LED equivalent is a 1157 LED Bulb. The Honda bulb with part number 34902-259-003 is a 12-volt, 3.4-watt bulb featuring a BA9S base. The GE 53 bulb is a 14.4-volt...

Thats a Good Idea. I like that! They also make a Blank red ring for the Lamp Test button! Thanks!

Thanks Peter, I’ve edited the question to be a bit more clear on my asking for the LED Bulb. I do have the markings and I’ve researched the bulb a bit, and the LED options look like crap. They don’t seem like they would fit in the rubber push-in’s on my Dash. I’m not looking for super bright...

194151-55820 - Yanmar, Bulb, 12V3.4W (inscribed markings NSN 12V3.4W) Also known as: HONDA OEM BULB 12V 3.4W) | 34902-259-003 With a BA9S base. The apparent LED equivalent is a 1157 LED Bulb. Has anyone found a replacement LED version of this bulb that they like and works well for them...

Yes, I could not find a Link for the Green. Attached are the Cans I used. For the white and black and spend a bit more on the enamel. I know the White is more white than the slight cream color, but I'm good with that. Here is one of the side Panels and the 'Console' portion of the body

Here are some updates. This is using the Gloss Apple Red334024 and the Spruce Green

I'm trying to fix up a Yanmar YM2002D. While fixing it mechanically, Thought it would be good to paint too. I've read thought the 5 Pages and have started on using the Gloss Apple Red334024 On the 'Body' I've got no clue. I think it's a Green color, though there is some kind of goldish pain...

I’ll Check out the lines out, though I am getting flow to the Hydraulic valve Controller, It gushed out of the input there when I loosened the connectors.

I was able to remove the bucket controls from the line. So it’s just the screen, filter, Pump QuickConnect, then back into Hydraulic control valve. 3Pt was still wacky. Pressure gauge shows not even 500PSI when put inline. Pressure gauge pegged passed 3000 when I cranked the engine (no...

Okay, here is more info. Still have jerky minimal control for a few moments after start up. What I've taken apart/seen. Intake Screen - cleaned Pump seems to be able to build pressure, cant seem to sustain it. Took apart the relief valve to the parts shown- Spring and valve pin. Valve pin...

The Filter Screen (not screw?) is the original that has been working for years and years. I dont think the filter screen, or the intake are the issue. I’ll Check out the Link… Thank you!

He Quick Connect was installed after the Bucket controls and before the return to the Hydraulic Case. It allowed the connection to add a Top/Side link control for the 3 Point. Though I’ve removed that and have the Bucket controls going back into the Hydraulic Case directly vs the 3Pt Control...

Thank you. I updated the Question. It’s a YM2002D. No Hydraulic control. Only thing not taken apart is the Hydraulic control case/relieve valve box. Seems like its not keeping the pressure from the Pump.