Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Marketplace
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
TractorTech's latest activity
T
TractorTech
reacted to
orville's post
in the thread
Replace hydraulic pump on 2005 TC30
with
Good Post
.
I got it! We took enough extensions to make a 2 foot long one. With the help of a swivel and a 12 mm socket we crawled under the front...
Saturday at 4:01 PM
T
TractorTech
replied to the thread
Massey Ferguson 4707 Fuel Tank removal
.
Drain it, remove the wheel, unvolt the straps, remove the sender wires and the fuel lines.
Friday at 9:50 PM
T
TractorTech
replied to the thread
1920 ford
.
I would think you could take some that fit a Kubota, Deere or NH like these and modify to fit your 1920. MT40279792 STABILIZER $70.04...
Thursday at 9:53 PM
T
TractorTech
reacted to
Goss's post
in the thread
Ford 7410 loader on a Ford 6600 Tractor?
with
Good Post
.
Interesting link. Thank you. From what I can find, strength wise it should be ok for an 80hp tractor.
Thursday at 12:44 AM
T
TractorTech
replied to the thread
Honda H6522 (A4)
.
Welcome to TBN! Sounds like an ignition switch problem
Thursday at 12:10 AM
T
TractorTech
replied to the thread
Ford 7410 loader on a Ford 6600 Tractor?
.
Most likely the same bolt pattern, but the 4630 is a 3 cylinder and the 6600 is a 4 cylinder. Look at the parts book for differences in...
Thursday at 12:06 AM
T
TractorTech
replied to the thread
Ford 4000 power steering
.
That is a single cylinder on the LHS. The cylinder portion is 1-4. The rest is the actuator.
May 1, 2024
T
TractorTech
reacted to
Dman1981's post
in the thread
Ford 4000 power steering
with
Good Post
.
Yes your control valve is on cylinder if it is over tightened it will stick and stay on causing oil to get hot Or piston seal is cut...
May 1, 2024
T
TractorTech
replied to the thread
Massey Ferguson 50E Power Shuttle, how can I tell the year?
.
What do you want to know? It has a 4 cylinder Perkins. It later became a Fermec, then Terex. Not much info on industrial MF serial...
Apr 29, 2024
T
TractorTech
reacted to
Wagtail's post
in the thread
53 Jubilee
with
Good Post
.
G'day Mate. Here's what tractordata.com has to say about your tractor, including serial numbers & location...
Apr 29, 2024
T
TractorTech
replied to the thread
Ford 5000 gasket
.
You have water passages (oblong holes) on the other side of the bolt holes. Not sure why those holes you circled are blocked, but not to...
Apr 28, 2024
T
TractorTech
replied to the thread
53 Jubilee
.
Welcome to TBN. That is a casting number for the block...raised letters. Early NAA models the serial number was on the left front of...
Apr 28, 2024
T
TractorTech
replied to the thread
hyd remote
.
I believe the only orings you will have are on each end. I don't have answer for your second question
Apr 28, 2024
T
TractorTech
reacted to
BourbonFarm's post
in the thread
HELP! Howard Rotavator pto shaft
with
Good Post
.
No, it is some irregular spline pattern.
Apr 28, 2024
T
TractorTech
replied to the thread
HELP! Howard Rotavator pto shaft
.
If you have the implemrnt side of the PTO shaft, why not just get the tractor half shaft? Tube is rectangular, yes?
Apr 27, 2024
Forums
Top