Search results

Thank You

Thank You for responding with good info

1960's John Deere 2010 utility tractor power steering issue. I am a retired Mechanical Maintenance person wanting to help my son, who is a hobby farmer. I am looking for some verbal help or pictures relating to a 1960's John Deere 2010 utility tractor power steering issue. The tractor has...

I didn't read all the posts, but I will add a little info. I have been to a lot of quarries or bulk loading docks where they have rules that the driver must stay in the truck at all times. That may work for the big dump trucks with automated tarps and such. but I like to do a walk around making...

my John Deere 520 when the engine is running the tractor ammeter fluctuates radically on both sides of 0. Just bought the tractor and it has a new battery in it. It has all original wiring and still has a 12 volt generator with positive ground. the battery voltage seems be ok, with a hand held...

I have a 660 Ford [600 series] I have only owned this tractor for 3 years and don't know the history - I recently replaced the distributor cap and rotor - the old rotor had a little medal clip that went in side the rotor shaft hole. I tried to put the clip into the new rotor, but could not see...

I use a Ford 660 tractor for club tractor rides and I would like to temporarily tie rear brake pedals together whenever I am on the road. I was wondering if anyone has done this before, so that I don't have to reinvent the wheel. Thank you in advance. Klink

Hi How hard and or expensive is it to replace a bad TA in a IH 350. I've never had any experience in replacing or repairing a TA on old Farmalls. Any and all info would be appreciated on the subject. I did not do much searching in forums on the subject. Thanks klink

Hi My John Deere 50 is a hard steering tractor, with an extra hard spot about half way through a full turn when turning left. I took off the front nose hood cover and checked the oil level in top steering gear box - it has plenty of oil in it. that's as far as I have gotten. I plan on blocking...

Where can I get a side cone drive pto clutch drive pad disc. I live in NW Ohio area. I need to know where a Wheel Horse salvage yard is at. or any help in locating cone pto clutch parts. I don't think we have a Toro-Wheel Horse dealer in Findlay, Ohio. Klink

I had the main fuel needle out of the carb & was blowing light air from compressor into the various carb holes to get any dirt out. Out of the corner of my eye I seen some thing fly out of the main fuel jet hole on top of carb. I looked around but could not find anything. I know I blew something...

I have a Cub Cadet 1541 with a very slow reverse speed. I was wandering if anyone has ever found a way to speed the reverse speed a little faster. I realize that reverse should be slower than forward speeds, but mine is really slow in reverse. Any insight on this problem is welcome. klink

I want a Pequea 1020sst [ 12k x 20' ] trailer with 8 bolt hubs, new 235/80R/16 tires, 10k drop leg jack, led lights, 6' spring assist ladder ramps, one spare tire. Price quoted - with tax included - $6750. I would appreciate some feed back from some of you, that have priced out similar...

I have 2 John Deere mowing tractors ( GX345 & X540 ) with 54" mower decks. I don't like the high suction blades. They suck up stones along driveways and throw them out. Also their shape makes it hard to sharpen them. I would like to try a set of aftermarket straight blades that just cut grass...

My son asked me to make a calf or cow walker tractor hitch to use to train larger calfs to walk with his teenage kids. I know, they should walk the calfs daily, so that it is a gradual training process. Last years dairy show calfs are going back to the fair again this coming summer. So I'm...

I have a water saver shower head in our shower - it sings as the water pressure goes up and down - it is a high pitched sound - we have a country well system with a submergable pump any help would be appreciated.

I'm trying to heat a porch enclosure and keep the temp down to 50 degrees. I purchased an Eden Pure electric heater, and it works great. But I can't get it to stay below 62 degrees, even at its lowest setting. Do any of you know of an electric heater that will maintain the temp down to 50...

I was at a plow day last Sat. I lost the front coulter and retaining collar clamp [ John Deere part # D 414 A ] later I found the coulter disc - but could not find the coulter retaining clamp. I need help locating a salvaged replacement part. Who sells vintage plow parts?

I have a JD Model #412 Plow - which is a 3 pt. 2 -14" bottom plow. This plow was made for the JD Model 40 tractor with 3 pt hitch. I have a 1954 JD 50 tractor with no three point hitch. Yet!! I'm thinking about mounting this plow on to the 1954 JD 50 with an after market 3 pt hitch. My...

I 'm looking for a OEM Dual Selective Control Valve for a John Deere 670 compact tractor. I want to mount a loader on this tractor.

Haywire I'm 64 yrs. old. The implement & weights prices were still the lowest price I could find on the aerator - apples to apples. Also with today's fuel costs going up daily. The shipping is a very big cost item. My order was around 1500 lbs going 700 miles - go figure

Back in March of this year 2011, I bought a 3pt 48" core aerator and aftermarket suitcase weights that fit & work just like green weights. I'm very satified with the equipment. Chris & Rick and rest of the gang were good to deal with. When I am ready to buy another implement, I will consider...

I was mowing grass and chopping up leaves today. I like this tractor, it only has 18 hp, but it does everything I want. The 55 & 70 series are great tractors. One of my goals for this tractor is to get narrower R1 rear tires and then get a 3 pt. one bottom plow for it. Then I'll have another...

I 'm thinking about buying a new FBR Gaspardo 3 pt. sickle bar mower. Would like some owner feed back about it. I need to mow property lines, under evergreen trees, along creek bank, along road ways. I use a JD I-match quick hitch on my tractors. It appears that Dealers don't stock these...

I put a power beyond kit on my JD 4110 hst tractor. my tractor already had a scv for the loader on it. Now I want to install an extra directional valve to operate my power angle blade. My question is-- does the extra directional valve have to have a relief valve in the valve body?? or My...

The owners manual for my JD 4110 only mentions glow plugs once, containing very little information. My question is - does my 2004 - 4110 have glow plugs and what is the best way to use them? Since there is no indicator light. Thanks