Search results

So my tractor won’t start after replacing the battery. I was jump starting the tractor without a battery, using my truck, now I can’t get any signs of life on the tractor. I also replaced a fuel line. Any ideas?

I found a rats nest in my kubota, I was wondering what these fuel lines are for?

just got a flat tire, air and water were leaking out of the valve, what should i do?

i am planting my cover crop ASAP. i am using a broadcast cone spreader, how fast should i be driving? i have a Hydrostat, i am thinking High gear, PTO @ 540rpm

i have a new splitter that is hooked up to the rear hydraulics that i use for my BackHoe or TNT on my Kubota L3010. the problem is that the cylinder only extends outwards, and does not go backwards.

with all this talk about discs and rototillers, people with small tractors should know that there are real discs out there that actually do a great job. I am super fired up on this 4 foot, pull behind, offset bad dog, because it has transport wheels,brand new blades, really cuts deep, and has...

it's time to change the hydraulic fluid on the tractor again, which i have done before, my question is what should i do about the implements that have fluid in them? such as loader, which is on the tractor, and backhoe, TnT, hydraulic lift disc, and potatoe digger, which all have fluid in them.

I am rebuilding a JD #44 plow, 3 point, 2 bottom, and I can not find plow shares. The JD dealer is having much luck for finding "DEERE BC 250." Can anyone find these?

i have a JD #44 plow, 2 bottom, 3 point, that needs new shares, the old ones say 'Deere BC 250". i took it to a JD dealer and had no luck. any suggestions.

slowly rebuiding an old offset disc. I ordered new discs and the hole where the 1 1/8 " square axle/gang bolt goes through the disc is 1/8" too big. The guy at the shop said that is the way it is supposed to be sloppy, but the old one's fit snug. I need some more clarification that the discs...

I am trying to rebuild a old 4 foot offset drag disc with hydraulic lift wheels. I got the end nut off the axle and one disc off. Do i just knock the axle with a block of wood and a sledge?

just got a great old rusty offset disc that needs a rebuild. how do I get the blades off.

this is the first time that I have tried to change the hydraulic fluid in my L3010 hst. I am having 4 problems. 1-I can't get the rear drain plugs on rear axels off. 2-I can't find the strainer, I had TNT installed, I does the strainer have a picture of a book on it. 3-I can't get the...

1 1/8\"cultivator clamps I have a farmall Cub tractor with a belly mounted 11/8" diamond toolbar. Where can I get some cultivator clamps?

What is the maximum width between the rear tires on the Kubota L3010? I know there is 48" on center, currently 52" on center, and there are two more, but do not what they are. I can't find my book. At the current 52" spacing, there is about 20" between drawbar and inside of right tire. I...

What is the proper spacing of the rear tires for a 2-14 plow? Currently the tires are 52" on center and are 39" inside to inside. I heard that it should be narrower. Is alright to change the width on only one of the rear tires? Also, what is best size and type of a drag disc for a 30hp 4wd...

I am thinking about attaching a multimount winch to my Kubota L3010. I might weld a receiver hitch to a box scraper, or would a 3 point receiver be stronger. What about attaching the winch to the front of tractor?

i want to add draft control to my kubota 3010. how difficult and how much will this cost?

I have Kubota 3010 and want to add draft control for the better operatation of a 3 pt pto potato digger. How much? How do I do it? Is it possible to disengage it?

I am looking around for a used offset pull disc for a 30 hp 4wd tractor. Is a 6 footer too big? I found 5 footer for $600. A friend got a 6 footer for $200

I have 3010 4wd- -the narrowest tread in the manual is 44 inche centers with the discs turned outward. - However, the manual infers that I should not flip the discs inward on the small model tractor. -Is it safe to flip the discs inward? -I have a Cub tractor that I hill potatoes with on 40...

I have 3010 4wd- should I pull a 6 foot offset disc?

I am trying to pack the soil after my tillage to seal the moisture in the soil. I made a 5 foot roller out of a 8 inch cardboard tube full of concrete with a 2 inch pipe in the center that is threaded with a chain to drag behind a tiller. The problem is that it did pack the dirt as hard as...

Is necessary to rip behind the tire tracks before tilling to achieve maximum depth?