Search results

I have a like tractor under the bobcat label. On the firewall-on left side there are a set of relays. From vibration alone, the wiring can become dislodged from the relays slightly. These glow plug relays are a common part for failure as well. I keep a spare at all times as they’re relatively...

rScotty, I’m certainly happy with it. I did change the header to RESOLVED. On top of page just above the posts, there are three small dots. You can access what was written and add what you’d like from there.

I have put 25 hours on it now. Runs great, no codes, no issues at all. A little light in the rear for such a strong loader, but I will overcome that.

Resolved…manifold sensors were not plugged in after rebuild. Entirely my own fault. all is well with this tractor now. Thank you all for your input. It’s not always necessary to involve dealer. We can still lean on one another and that is appreciated!

Jd110 and anyone else interested, it was because of those two plugs not being plugged in that I had so many codes. Today I cleared all codes and started it up. It warmed up to temp with no lights on the dash. Once temp was reached, it went to asking for a parked regen. After doing the regen, all...

Thank you for taking interest in this issue. I found, about two hours ago, that neither of the plugs on the bottom of the manifold were plugged back in. One being the manifold temp sensor and the other the manifold pressure sensor. This was my error entirely. Incidentally, those are on the same...

Definitely not a mouse issue…but there’s a chance of damage to wiring simply from moving them to take off the head. I don’t think that’s the issue, but it’s possible. As I said, I ran it long enough to get antifreeze up through the heat system. I didn’t allow it to idle below 1200 rpm until...

If I could delete this, I would. I’m not looking for DIFFERENT answers, just answers. So far, only two, ruff dog who was trying his best to be helpful and you, worried about where this is posted. Do you happen to have any input about the issues?

It has really good everything else, just a bad set of rings. Inside of cab isn’t worn, outside it looks great. The loader bucket hasn’t been used much as there’s still paint in the bucket. When cleaning it, there was a lot of sand. My guess is he used it in a hay field and didn’t know he could...

I’m not looking for DIFFERENT answers, but I am looking for answers. The reason for the new post is to move it from owning/operating to here. Do you have any answers or are you simply off put by me moving the post?

This is a 2106 5055E cab tractor with 12x12 PR transmission with 800+ hours bought at auction that needed a rebuild. I drove this tractor and even loaded it after purchase. I have no previous history for it. When I got it home, it barely had enough compression to crank, but had no lights on the...

It had no power before the rebuild. It has plenty of power and compression now. Except it is derated. Never having a tractor with DPF, I can’t say what exhaust flow is or should be. It sounds right, but that means nothing really as I only have this tractor to judge that from. But again…it did...

It ran great, but had no power. The fuel in it has been replaced with fresh diesel from my tank with a filter. Fresh coolant and new oil. Fluids shouldn’t be my issue as they’ve all been changed. All of the filters have also been changed, even the cab filters. I only ran it long enough to ensure...

No. As I said, it wasn’t asking for anything before the rebuild. I didn’t want to change the parameters unnecessarily as I realize how sensitive sensors can be.

This is a 2106 5055E cab tractor with 12x12 PR transmission with 800+ hours bought at auction that needed a rebuild. I drove this tractor and even loaded it after purchase. I have no previous history for it. When I got it home, it barely had enough compression to crank, but had no lights on the...

Attempt what with a backhoe? I use these all the time with backhoe, excavator, lifts, skid steers, pickups, etc… In fact, we usually place them with a backhoe or 5K reach lift.

The plastic mats are a lot less weight than swamp mats made of creosote ties. In fact, a small loader can place them with ease. When renting these, plan to rent as many as needed to road in to where the work will happen. If you need a platform to work off of, measure the area and rent all at...

I agree with a lot of what you said. As we age, those lights seem brighter, not to mention the change in law about lighting. They’re literally more intense than they once were. You should know though…I drive a 2018 F-350 single wheel and turned off my seatbelt warning because I drive around job...

I think people believe kubota uses a locked rear. They use a limited slip with the ability to lock as does a tractor. You can also buy, stock, turf tires installed instead of their all terrains.

Here in Texas, you can do that with your Ag card. No matter the brand. My kubotas were bought as business but Kawasaki’s we’re farm use.

Well…I install artificial turf for a living and use the kubotas for that a lot! You see my work on Sundays. Those aren’t torn up….

That’s pretty awesome. But, it’s better to have it and not need it than vise versa. I just can’t be a cheerleader for the Polaris company. Mine has a lot of issues, small, but always something. Plus I know three different guys that have issues with transmission levers. Not sure why, I’d have to...

I should also add…speeds of the teryx are way faster than I ever want to go, that leaves me power and torque to get moving. Like I said before, the mule pro is very car like and can go pretty fast, never topped out, don’t know but probably 40 ish. The kubotas will go 26 mph if you have the...

For what it’s worth…I have a Kawasaki teryx, Kawasaki mule pro and two kubota RTV x900s. I do a lot of ranch work and all have their benefits. The first is…Kawasaki offers a three year warranty. Every other mfg offers one year. This is huge for me. That being said, the kubota machines are strong...

I am with Tman on this. It either sounds like air or you have a bleed, possibly in the joystick where some pressure is getting to up/down and curl up/down. A simple seal leak can make your hydraulics seem weak. To answer your question, I usually have something on the 3 point, heavy old forklift...

I guess the reason I’m struggling with your issue is my personal experience is so drastically different. I can literally lift the rear of the tractor by curling the bucket. Although I do not move hay with the loader, I do use this tractor for a lot of lifting tasks. I don’t think I have ever...

I have a ct225 that is very strong In hydraulics for the size of the machine. The thing some folks forget is the weight of the pallet forks or whatever attachment is on the loader. I know my forks are extremely heavy duty and weigh quite a lot. Be sure you’re factoring the weight of the...

Just an old country boys opinion here... 14k trailer even if you think you would not need it. You have made an investment in buying your tractor and equipment, as well as your truck. Why take a chance on an inferior trailer? Here is an example for you guys... I used to own a Big Tex 14LX dump...

Winston, I was really limited to bobcat. North texas guys, the store south of Dallas Was closest to me. He (My local guy) did an excellent job of putting it back together very thorough. Changed every fluid, every filter, greased it up real good, heck he even built me a battery hold down. Wasn’t...

Hello, all. Well, the little ct225 is finally running. I have had it back about a month now and put some solid hours on it. I have to say, I am very impressed. Never had a compact or a HST before, except a lawnmower...really easy to use. Hydraulics are quick and strong, pushed over a half dozen...

Hi everyone! New to site. I have been looking at posts for a long time. I have way too many tractors not to! Here is what I have going on and hope for help. CT225 turns over fine, but will not start. 1. Starting from the beginning, the only things that will keep it from CRANKING would be the...

Hi everyone! New to site. I have been looking at posts for a long time. I have way too many tractors not to! Here is what I have going on and hope for help. CT225 turns over fine, but will not start. 1. Starting from the beginning, the only things that will keep it from CRANKING would be the...