Search results

Greetings. Has anyone changed the oil pressure relief valve on a daedong 4a200 engine. I recently tore my engine down and replaced the oil pump as well as Camshaft gear. Both were destroyed. I still don't have enough oil pressure to make the oil pressure light go out. Also does anyone know what...

Looking for a brand of backhoe still selling subframes for a 4110. Also has anyone tried to find a TYM or Kioti subframe that would fit? I know the frame is tym and the engine is Daedong (kioti).

I have a 2004 Mahindra and as of yesterday it won't start. If i turn the key i hear a relay chatter ( i think either the signal light one or another one beside that. If I turn on glow plugs a relay by the horn chatters. I looked at the ground and battery connections. everything looks ok. I am...

Has anyone replaced the gun on a Lincoln SP170T? I am trying to figure out if the Tweco no 1 gun would fit. I know it takes a magnum 100L 3080-1 Lincoln gun and I know that Tweco guns fit some Lincolns. Tweco looks to be cheaper most places i looked.

2 of the bolts securing the front axle fell out and the other two were loose (never thought to check these during maintenance). By time i figured out what happened the axle had rolled forward pulling the drive shaft with it. I got it back in place and stole some wheel rim bolts to secure the...

Do you have any 100o rpm implements? If your tractor is equiped with a 540/1000 selector, do you use the 1000 rpm speed with any of your 540 rpm implements? I am considering disabling the 1000rpm on my tractor during a repair to the 540 gearing to fix damage caused becuase it did not fully...

My PTO on my 4110 will not run in 540. it will run in the 1000rpm setting. When I start the pto in 540, the selector lever jumps a couple times and drops out to neutral. Holding it engaged gives me the distinct impression that the gears have been damaged. I suspect someone stepped on the lever...

I built this as a father's day gift for my father .....

Can someone take some pictures of their Cub Cadet 1863 or 1864 throttle assembly for me. A spring fell off the underside while replacing the throttle cable and it is not obvious where it goes. Thanks in Advance.

I am trying to choose my next 3pt attachment. I sold a 3 bttm plow and a pull type cultivator when I moved and now will need some tillage equipment again. I am not ready to drop 2k for a tiller wide enough to cover the 6' track of my tractor. I am trying to choose one tool for under 1k to...

This week I added accent lighting to the underside of the frontend. I think I will need two more lights under the operator platform. They are wired to a toggle switch I added to the dash.

I am not pushing anyone to retrofit old tractors, but I thought any New York state TBNers who feel the need should know about this... NYCAMH/NEC - News - NYS ROPS Retrofit Update

I found this by the side of the road. They are asking $4500 with the 5' finish mower. It is very clean, but I 'm not sure it's worth that much. So far I know.... It's 23 yrs old It's a 2 cylinder diesel It's very clean, well greased, and has new filters Some new spindle bearings on mower Front...

I am mulling over how to build a device to plant pumpkins. This year I will only have 80 hills, but I want to get up to 150 - 200 hills next year and up to 400 hills in a couple years. We hand planted over 600 hills in 2005 with about 5 people and I don't want to do it that way again. These...

This weekend I am starting the project to install fencing so that we can finally bring the kids' pony to our new home. I picked materials and have started drilling the holes. I don't have any progress pics yet, just one of materials. I am going with 4 x 4 PT for the posts. I also have some 2 x...

We are starting some new flower gardens at the new house. I leveled up the ground with sand and we set three rows of blocks from the local big-box store. My wife duplicated the process around the corner on the next wall too. We only had enough stone on the partial skid I bought to get two rows...

I got sick of the jack on the utility trailer hitting the tail light or rack every time I move it with the ATV. I will need to make a custom insert for the ball that is usually on there. I have a 1 7/8" ball with 5/8" tapped hole in the bottom instead of the typical 3/4" stud. I will buil it...

I recently tore the hose off the back of the hydraulic filter on my 4110. I removed the filter housing while I straightened the bracket it sits on. Everything is back where it belongs (more or less) and I filled the oil back up, but it sat for 3 days with no oil and it appears the pump needs to...

My Kawasaki is about 7 years old and recently it started leaking gas out of somewhere on the engine. It stopped leaking when I brought it home and has started again. It looks like it is running out of the air intake. I am thinking stuck float. Does this make sense. I am not a small engine...

I am looking for opinoins on a chainsaw for light to moderate use. I have used mostly Homelite in the past. I want something around 3.6 Cu. In. with a 16 or 18" bar (like the Stihl MS310). I have Husky, Stihl, and Jonsered dealers all nearby. (real dealers, not Walmart).

Has anyone modified the loader mount on a 4110 to add a brush guard? My grill got damaged last week when a root ball rolled over and a root snapped against the grill. I am thinking of adding three bars of 3/4" roundstock across the front of the loader frame between the two upright plates. I...

I moved to a new place last December and am now faced with clearing land for growing a large garden and a serious drainage problem with drainage at the wood line. This is a picture of the woodline and standing water on the lawn. The trail into the woods was already there, but abandoned.

I bought the male fittings for my quick connects from my dealer over a year ago. I just got around to buying a hydraulic top link and went to plug the fittings in for the first time. The problem is, they don't fit. They are stmped Stucchi-M-BIR 12 NPTF-K04. I can't make out enough of the...

This was my birthday cake this year.

Has anyone used a 3 pt hitch dirt scoop to dig ditches? I need to dig a few hundred feet of ditches and I am considering buying a dirt scoop for the job. The ditches dont need to be more than about 18" deep and 2 ft wide would be fine.

I haven't had any luck finding logo merchandise yet, has anyone else found any. I haven't tried the dealer yet. I may stop by a dealer and see.

DOES ANYONE HAVE A SOURCE FOR PARTS FOR OLDER MASSEY IMPLEMENTS. I NEED NEW POINTS FOR IT. THE MASSEY PART NUMBER IS 660620M1. A MASSEY DEALER DOWNSTATE TOLD ME HE COULDN'T GET PARTS FOR MY PLOW(OBSOLETE).

Last night I was back dragging to fill a hole with dirt when I lost all loader functions. I was pushing the bucket into the dirt pile. Power steering and 3pt still work, so I am guessing it is the pressure relief on the loader circuit. If anyone has a quick fix let me know, otherwise I will...

Does anyone know how much oil is needed for a change-out?

I had my tractor at my fathers this weekend to help with some chores and the four wheel drive started making alot of noise. I have heard the noise before when going into or out of 4wd, but It became a big issue yesterday. Now, every time I go in or out of 4wd I have to play with the 4wd lever a...

A friend of mine bought a 2615hst w/ FEL for $13,800 yesterday. I also know someone was quoted $16,700 for a 3510.

I picked up a skidsteer style toolholder from my dealer today for my 4110 with a ML112 loader. Several dimensions are differnet than on my direct mounted bucket. The center distance for the loader arms/cylinders is slightly larger (1/4"). It will be a tight fit, but I think it will go on...

I have 134 hrs on my 4110. I took it out of 4wd for the first time in two months today and it started making some transmission noise. It doesn't sound like a gear meshing problem, more like two components rubbing. It is a little louder with more speed. I also found oil leaking from the area...

I am looking for manuals for a Renault N70 tractor for a friend. Preferably in English. I know this is a long shot, but he is trying to get it running right and manuals would certianly help. Also he is having lots of problems with finding parts. I had an IH 384 that was from england and...

I am getting a set of Dearborn drag discs from a friend and they need some work. Bushings will need to be replaced as well as a few of the discs. Does anyone know a good place to order parts for old/antique/obsolete farm implements.

I am accustomed to seeing some smoke for a few minutes at start up in cold weather(below freezing), but last night I could some in the light beams from my aux. lighting the whole time I was working. It was actually a little warmer last night (34 degrees) and there was no wind. It did not smell...

I found a Massey 1655 garden tractor with ag tires, 3 pt hitch, and snow blower advertised locally for $900 (No mower deck). Is that a good price? Can I put a small loader on that?

I am considering modifying my KMW loader on my Mahindra 4110. I want to be able to switch buckets. I only have one now, but I want to build a forklift / grapple attachment later. Would it be best to use an ATI skidsteer adapter or is there some other design that would allow me to buy...

After abusing my 3 point hitch a few weeks ago, I noticed it has started drifting down when not running. It takes about 2 days to drift down. I got a post hole auger stuck in the ground and instead of disconnecting it I drove forward and dragged it out of the ground. I don't see how this...

My father has a JD790 and recently looked into a front mount snow blower for it. I think the price he got was at the dealer that sold him the tractor 4-5 years ago. He was quoted around $4000.00 including the kit to install the mid mount PTO. Installation not included in the price. Has anyone...