Search results

I have a bobcat 853. I am trying to install the to window for the cab so far it has been next to impossible. The seal has to stay in place I taped it on the from side since that is the only place you can wrap the tape around. Now trying to install the window into the grove and the glass will now...

I was able to find a YKMT43 rototiller the 2000 rpm for my YM 146 Yanmar. Tiller had some leaks around the pillow block bearing so I am replacing those now. It came with a manual so I have the diagrams. Has anyone else ever did maintenance on one of these?

I am painting my YM-146 what do you think should I make the last coat a clear coat for protection and shine?

I created and printed this shift-plate cover for my Yanmar YM-146. I used an Ultimaker 5S to print and designed using Tinkercad. I already had a plasma cut plate for the shift positions so I attached that to the plate. The plate is much tougher than the original which cannot be purchased and is...

I have a YM146 and I recently replaced the steering shaft and bearings and I had to disconnect the shifting linkage. But now that I have put it back together when I try to shift from reverse back to neutral it is very hard to shift. I have sprayed to shift cable with lube but that did no good...

I just finished my custom designed plasma cut front grill with LED lights. I came out very nice. I used inkscape to create the file with the cutouts and bolt pattern. Then I had it plasma cut at the shop. The model letters are also plasma cut and spot welded to the light grill plate. I taped off...

I have a Yanmar YM-146 same as the GT-14 and very similar to the YM-122 The bearings are shot on the rear clutch yoke and a recently purchase a for parts YM-146 for a steal at $50 and it has a good yoke. Hear are some pics of the part and the part from the breakdown page. The part number is...

I have add LED lights to my front grill of my YM-146. I also added a custom grill and name plate. I have also added a racing alternator to replace the dynamo with the regulator which burns out all the time. And I added a custom made 3 Point hitch. Now all I need is to find a mower deck that will...

I am going to build a 3 point hitch for my YM-146 aka GT-14. I am wondering if someone can help me with some measurements. The schematic shows the components I am looking for the length of part 5 and its diameter. I would also like to know how far part number 2 is from the part number 9. What...

My deck bit the dust so I got a new spindle and it was too short. So I was gonna make a weld on hub that was shorter but couldn't find a short hub. I was frustrated. Then an email came from a craigslist ad that I sent out over a month ago. I guy had a yanmar YMM-45 that had never been used just...

Fuse keeps blowing on fuel pump curcuit. Has anyone else had this problem with a fuel pump curcuit. I have a YM146 also know as the GT14. Just wondering if this is a common problem before I start to trouble shoot. Never hurts to ask before you jump in.

My tractor died yesterday so I checked the fuel line and noticed it had a lot of bubbles in it. I thought it might have a clogged fuel filter. I replaced it and tried to bleed the system. The fuel pump continued to sputter and I never could get it to shoot out a clear stream of diesel. Any ideas?

How do I install rear axle seal on YM165D? Anyone ever had to work on the rear axles of one of these? I need to replace a seal, it is leaking fluid and I cannot figure out an easy way to do it.

How do I replace Rear axle oil seal YM165D? I have a parts manual but want some pointer before I tackle this job. Oil is leaking from the left side axle. Thank you.

Does anyone know of a way to test a regulator? My tractor used a generator/regulator setup. Now I what to know if the regulator is good or bad.

I have a strange noise coming from behind the oil filter. The noise sounds like a bearing rotating around. It is loudest when I first start the tractor a YM146 same as a GT14. Before I get into it I would like to know if anyone else has had any problems like this. I also have a voltage regulator...

Has anyone every installed a alternator and replacing the generator on a YM146 or simular tractor? The reason I am thinking of doing this is because the voltage regulators keep going out I have replaced it 3 times.

Anyone have any ideas on how to install a Hypro Roller pump to a YM165D? I have a PTO coupler and would like to know the standard way of hooking these up before I make something up on my own.

What is the equivalent turf tire that will fit an YM165D for both front and back wheels? I have heard I need to make sure tire sizes have a certain ratio so the 4WD doesn't work against itself. I have also heard that I may need new wheel rims for the turf tires. Any info?

Does anyone have the specs on a YFL-155 Loader. Capacity, type and weight of Hydraulic Fluid, Lifting capacity ect.

I have Black sludge in Hyd Loader Lines and Valve assy. I have cleaned the valve. But how could I clean the lines. The loader I have has the hydraulic fluid inside one of the arms of the loader intself. I think it is a YFL-140 and it runs off a Hyd pump driven by the front PTO.

Can someone explain a Thermostart. I have a YM165D and it has a thermostart. There is a small bowl that feeds into the air intake. What do I do to use this.

Where is oil pump on YM165? I don't have a parts manual yet and the owners manual seems to show that you get at it from the Flywheel housing. Does this mean I have to completly remove the motor to access the oil pump?

I have been gifted a YM165D Yanmar that has been sitting for 8 years. It only has 300Hours on it but it still has some problems. It still had all fluids intact so I drained all of them and refilled and put in new filters, Oil, fuel, Front gear box. The tractor was missing the starter and the oil...

A weird problem but the dip stick to the rear gear case is stuck solid. I have tried turning it prying it hook vise grips to it. The only thing that is happening is the rubber is about to break off the dipstick. Any ideas? I have a YM165D.

I have a YM165D. I just got a new starter and it won't engage. If someone has a wiring diagram so I can check voltage to the starter I would appreciate it. Thanks Dan

I just bought a starter for my YM165 tractor. The guy says it is PN S114-230. The starter I got wont engage the flywheel the pinion gear doesn't stick out far enough. It is also a 9 tooth pinion gear. I have heard that these tractor take 9 tooth or a 11 tooth. How can I tell which starter works...

I have a YM165D. I am working on the tractor to see if the engine starts since it has been sitting for 5+years. It has a hydraulic pump attached to the front bumper that runs the front end loader. How to remove? The reason I think I should take it off is so the hyd pump doesn't turn without any...

I have a 2 cylinder diesel YM146 Yanmar. I have exhaust smoke coning out of dip stick hole and the breather vent tube. Oil has also been coming out. Any ideas what could cause this?

I have hydraulic fluid leaking and I believe it is coming from the pin hole in the reservoir fill cap. I noticed the hole when I tried to figure out where the leak was coming from. Has anyone else every had something like this happen. It squirts out every few minutes not a steady stream. I did...

I have a YM-146 14 HP Yanmar. White smoke is coming from somewhere. I can't figure out where the leak is located. Is there a trick or a likely spot that causes exhaust smoke to come out in unlikely areas.

Here is my attempt to fab a 3 pt hitch for my YM146 tractor. Here is the drawing I started with.

I have a GT14 tractor with a 2T75UN motor. In the bottom of the injector chamber is a copper gasket. This gasket is not shown in the parts manual. I purchased a chamber gasket PN: 124950-11450 but this is a soft metal gasket that fits higher up in the chamber. The copper gasket I am looking for...

I have a Yanmar GT14 with a hydraulic lift for the belly mower and 3 point what type of fluid do I need to put in. I had to drain the resevoir to fix a gasket on the motor.

I have a Yanmar GT14 same as YM14 and YM146. The engine is a 2T75U 2 cylinder diesel. It takes a long time to start. I heat up the glow plugs for 30-45 seconds then try to start. It turns over fine but doesn't ever fire up. I have to keep heating up the glow plugs 5-6 times before it finally...

I am fabricating a Cat 0 hitch that will fit a yanmar GT14 or YM146 I am looking for a couple of measurements. If anyone has these I would appreciate it. Here is a photo of the measurements I need.

I am looking for the following parts for my Yanmar GT14 tractor. It has a 2T75U-N Engine. I need 2 glow plugs 124970-77800 or cross Ref NGK Y-116V Oil Pan Gasket 12400-01750 Air Filter 171022-12530 or 121465-12510 So far I have not been able to find these parts except a dealer quoted me $45...

Where can I find a shop manual for a YM146 14HP garden tractor?

I have a Yanmar GT14. I am looking for a 3 Point hitch for my tractor that can use the hydraulic lift of my mower deck. I have a friend that can fabricate one if I can find a picture or schematic of one. So far I have been unsuccessful. Does anyone have a pic or schematic? Thank you in advance...