Search results

All: I was given a welder that has sat at our farm for a couple of years. I was hoping to buy a manual as it is in need of a little TLC. My dad didn't have much info on it, other than it ran when they sat it out there. Thanks for the help!

I had to replace the factory hydraulic tubes that lead to my rear remotes over the weekend. The problem that I need someone's help with is the hydraulic fitting on the end. It seems as though NH has applied some type of "glue" to these and for the life of me, I cannot get one of them to break...

Hi all, I need some help with a recently purchased sprayer. It started out as a good deal and has quickly gone downhill. I filled the original tank up with water and as I was pulling it out to my land, the side of the tank busted open. Good news is that my neighbor won't need to water anytime...

My first "dirt-working" implement. Super excited. Still a little hesitant about getting the roll over versus a traditional box blade, but went ahead and pulled the trigger.

I am looking at purchasing a rear blade for my workmaster 55. TSC has a 7 ft blade for $370. It weighs in around 230 lbs. The mahindra dealer here has a 7ft medium duty blade for $499. It weighs around 318 lbs. I was really looking for one in the 500 lb arena, but I know the prices jump...

What size do I use and where is the cheapest place to buy? I would call my dealer but somehow everything seems to be 2x the price. Thanks in advance.

Ok, officially tired of the hoses running to the rear of my tractor. I see there are kits that you can buy, and I have read the posts on here, but would like more specific information for my tractor. Please help.

All: Had to replace a hydraulic hose that is attached to my grapple and stretches back to my rear remote. Should I be concerned about air pockets or just hook it up and go?

As I was mowing today, I noticed a loud hiss coming from the left rear tire. When I stopped and checked it out, I notice the air was coming out of the valve stem. I couldn't get it stopped unfortunately and had quite a walk back to the truck. Anyways, my question is concerning the warranty on...

Just recently bought this tractor a couple of months ago and was wondering what aftermarket options are available? I notice there are a few holes in the left hand fender that looks like something could go there. I.e., toolbox, light, etc.

All: I have about fifteen acres that needs sprayed due to being over run by teasel. I can buy a sprayer for $350 that will basically cover 10 ft wide swaths. I can have it sprayed for $30 an acre. Basically, it would cost me close to the amount of the sprayer to have it done. My thinking is...

I realize this may be in the wrong spot, but i was not getting any action on this in the lawn and garden forum. I have 18 acres that is pretty much overrun with this stuff. Anyone have any experience in dealing with it? I am planning on buying a sprayer a little closer to fall, but unsure of...

I have 18 acres that is pretty much overrun with this stuff. Anyone have any experience in dealing with it?

I am currently looking for a box blade for my NH workmaster 55 and can't seem to decide on the size. My tractor is cat ll/cat l compatible on the 3 point. I was thinking that an 8 ft box blade would probably be the best size/match. Any thoughts?

I am looking at buying the attached bale carrier. I am a complete newbie at this so I wanted to get some thoughts/suggestions on this piece of equipment.

I know this topic has been talked about a lot on here, but wanted to get everyone's opinion. I can get my rear tires filled with Rimguard for around $485. To get them filled with the antifreeze, it would be around $300. I know there is about a 150 pound weight difference between the two. Is...

Hello all. I have been stalking these forums for quite a while and have finally decided to bite the bullet and buy a workmaster 55. I have a question on checking hydraulic fluid level on it. The manual is not real clear (or could be due to my inexperience). I had a leak on my grapple, and...