Search results

Results 1 to 22 of 22
  1. C

    Flail Mower bottom paint

    I have just finished changing bearings on the flail mower shaft. I have cleaned up the bottom of grass and mud. Since I am down there, I thought that I would clean some surface grass and mud and give it a good paint job. Certainly the crap enamel paint that came from the Chinese factory is...
  2. C

    EFGC155 Flail mower bearing pulley removal?

    I have a generic Chinese Flail mower EFGC155. It has a shot bearing. The shaft is vibrating and one bearing has a lot of play. I am i am trying to remove the belt pulley from the shaft. Can anyone tell me how to pull this belt pulley It has socket head screws which I have removed. It has...
  3. C

    MF135 Battery Cover Latch Straight Axel

    My straight axel diesel MF135 never had battery cover latches since I bought it. I thought I would buy and put these latches on. I ordered a Sparex S41228 battery clip for the lid. I am bit confused by the parts supplied and how they all are supposed to fit using the supplied parts. What is...
  4. C

    Oil & Fuel  MF135 Throttle footrest oil leak

    My Straight axel MF135 has a oil leak around the bolts on the Throttle footrest. I have tightened down the bolts but the leak is small but persistent. I cant see a gasket in the parts book between the footrest mount and the transmission body. Does anyone know if a gasket is used or just...
  5. C

    MF135 Rear 3rd Injector fuel line nut?

    In the process of bleeding my MF135 because of starting problem loosened the fuel lines near the injector. I also loosened the 3rd rear most injector line. When I screwed it back and did the bleed process again and then tightening the nut the not tightened right down till there was no thread...
  6. C

    Oil & Fuel  MF135 Clutch Inspection Plate Drawing

    I made a clutch inspection plate for my MF135. I have scanned the plate. I then cleaned the scan up in a drawing program. I would add 3 to 6mm to the edge since its rough ground with a angle grinder. Please check the hole sizes and location they seem alright on my MF135 but had to file some...
  7. C

    Oil & Fuel  MF135 Starting issue

    I have this starting issue with my MF135. 1. I cleaned the tank 2. Replaced the filters 3. Everything up to the injection pump has been purged and bled. 4. Replaced the lift pump with a new unit 5. Blew out all the fuel lines 6. Checked the glow plug and neutral safety switch wiring (no oil...
  8. C

    mf135 fuel sender

    After ordering and being sent the wrong fuel sender for my MF135 fuel tank, i though I would post the pertinent data. My MF135 has a larger capacity tank. There is a regular tank and the large capacity tank, the sender should match the type of tank. The Original sender on my large capacity...
  9. C

    MF135 Fuel Gauge and Sender info

    I have just been through the fuel sender and fuel gauge blues. Both my original sender and original meter were faulty. What is staggering is that it seems that where I live anyway most dealers seem clueless that the sender and the meter have to be matched. You cant get the impedance in ohms...
  10. C

    MF135 Tie rod ends removal

    Hi I am trying to replace the tie rod ends on my straight axel non radius MF135. I am having difficulty removing them. I have removed the nuts and I am trying to pop the ends out but they dont want to budge. Do I have remove the whole drag link and unscrew the end out or is there some...
  11. C

    M135 Multipower Hydraulic Filter Change Lift Cover or PTO cover?

    I have an early MF135 Straight Axel MultiPower. I want to change the hydraulic filter. I have an external hydraulic filter which I have removed. It was filthy and collapsed. The plan is to drain the hydraulic oil, flush with diesel and clean the multipower filter and at the same time replace...
  12. C

    mf135 Aux hydraulics PTO cover Multipower filter Hydraulic filter change

    Hi All I need to flush my Hydraulic system. I have Aux hydraulics fed through the PTO engagement lever cover. I have Multipower dual stage clutch MF135 Is it correct to say that if I want to replace the Hydraulic filter and clean the Multipower filter I have to go through the Liftcover...
  13. C

    SubSoiler MF135 Ripper?

    Hi Guys I have MF135 I have the choice of 2 sub-soiler sizes or rippers as we call them. I have the choice of 24 Inches(630mm) and 30 inches(780mm) Will the MF135 handle the 30 inch depth of these large Chinese mad sub soilers or rippers?
  14. C

    Massey Part Numbers

    These are the bushing and castle nut sleeve from my lower arms. These attach the lowers to the axle housing. Can anyone tell me the part numbers for these parts. There are no aftermarket parts available for these items. I have to order these originals directly from AGCO They look like cat2...
  15. C

    Massey 135 Clutch Hydraulics pumping sound?

    I am a relatively new owner of the a 135(3 weeks) I have been slowly sorting out and fixing all these issues. I am not sure if I have a dual clutch or single clutch because I cant find the serial number of the tractor yet. The tractor is running fine and the hydraulics appear to be working...
  16. C

    Castrol AgriMPplus 20w40 OZ Hydraulic and Engine?

    I have read the literature on this oil from Castrol. Its 20w40. They suggest that this oil can be used for the hydraulics as well as the main engine oil. Is this correct? I Believe a more suitable oil is 15W40 like Shell R4X. If this Castrol oil can be used as both as a engine and...
  17. C

    135 Parts Manual English Versus North American versions?

    Is there much difference between the English and North American versions of the parts manuals? I would like to get the parts manual and possibly have the choice of either version.
  18. C

    135 What is this filter?

    Can someone tell me what this filter is on my Massey 135. I cant find any reference to it in the manual. The lines run into the transmission housing so I suppose it is an hydraulic filter. I do understand that the Hydraulic filter is mounted inside the housing. Is this an addtional external...
  19. C

    Massey 135 AUX Hydraulics mounting

    My aux hydraulic pipe hose run under the 3 point link arms. As you can see in the picture the link arms hit the hoses when down. I want to fix this up because the hoses are very badly worn. Where is the best place to mount the output hoses and its brackets on a 135 tractor. I suppose anywhere...
  20. C

    135 Massey Clutch Inspection cover plate

    I have bad leaking around the clutch inspection cover. I went to tighten it up and found to my horror a piece of thin Aluminum/Aluminium sheet held on with Silicone. It looks like foil its so thin. I will try and get a cover. I might try and making one up in the mean time. Anyone have the...
  21. C

    Massey 135 Fuel Tank Line

    Hi I am flushing the fuel tank, and changing filters on my 135. I have a leak on the fuel line from the tank to the lift pump. My 135 it uses a black plastic fuel line about 1/4inch or less in diameter. Looks like hydraulic high pressure line rather than fuel line Was this common on the...
  22. C

    Steep Learning Curve

    Hi Group Just picked up a Massey Ferguson 135 after destroying numerous ride on mowers. A raw beginner but have learnt a lot just reading the forum. My 135 needs a bit of work so will be asking a few newbie question if I cant find the answers here. Writing this after replacing the water...
Top