Search results

I purchased a 16’ equipment trailer a while back which the previous owners had built boxes around the outside of the trailer forward of the fenders. The wood floor rotted out, and upon prepping to replace the floor, if found all kinds of sub-par welds… cracked, cold, no penetration, etc. I have...

It seems my 2555 does not have a fuel shut-off, so I don’t have a good way to prevent fuel from flowing when changing filters (or filter/lines are damaged). I’d like to put shut-off on my tractor. Does anyone happen to know the ID of the fuel line from the tank to the filter housing? I’ve tried...

Good afternoon, folks. I have a 2555 that developed a fuel leak yesterday after clearing some, apparently, 3000 year old muscadine grape vines. The leak appears to be coming from the water sensor on the bottom of the filter. This is now the second time a filter has been damaged by something...

Time to overhaul my 16’ equipment trailer, and while I have the floor torn off of it, I have been thinking about painting it. Does anyone out there have a recommendation for paint for the metal on my trailer? I’m sure some people just shoot Rust oleum on there, but I’m wondering if there is a...

Hey Folks! Let me start by saying that I have already e-mailed tech support on this, but I was curious if I’m the Lone Ranger with this problem. I have a 210STL that I bought a couple of years ago, and when I first bought it, it was bullet proof. I don’t even know how many consecutive days I...

Good Morning Everyone! I am wondering if anyone has any experience with Tractor Supply’s shielding gases for their welder(s). I have been renting bottles for a few years (1 I have no choice but to rent), but I am looking to move to smaller, owned bottles. Since I know no one will swap another...

Good morning! I have a 2555 which I have owned for at least 4 years. This past weekend, I was cutting a pasture when a piece of pine kicked up and hit my hydraulic filter. This caused the hose Union on the main hydraulic line to tear, the hydraulic filter housing bracket to twist, and me to...

Hey Folks, I recent did some culvert repair and extension. I want to level the area with dirt and then gravel it. I have a Mahindra 2555 with with no draft control on the 3-point, and 6’ box blade. The ground is not even, so do you have any recommendations on how to use the box blade to...

Good Morning Folks, I have a culvert that was installed (I assume) when the home was built, in 1991. In attempting to prep for extending the culvert to widen the driveway a bit, I found the existing culvert was… suboptimal. For starters, it had been completely covered with dirt, leaves, etc...

Good Evening, I have a 2555, and I have to move a lot of gravel soon. I am looking for any advice around building a ballast box (dimensions), and what kind of weight to use. I have looked for a suggested counterweight value, but I have not found one. The tractor has a Cat 1, 3 pt hitch. I was...

Hey Folks! Has anyone run into this issue before? We were brush hogging the pasture, and all of a sudden we started hearing a strange noise. After shutting everything down, and starting to troubleshoot, we found that if we manually turn the PTO, we hear a distinct CLICK about every 90 degrees...

Anyone know how to reach Mark @ Everlast outside of a PM? I’ve tried that route, and I have not heard anything back from him.

Hello, I was attempting to hardface a make-shift anvil for use at home, because real anvils are so dang expensive. Was putting on the hardfacing rod after pre-heating the block, and I saw what you see in the picture. I was even peening the beads, but it still cracked all over the place. What do...

Good Evening Folks, I have a situation that I am looking for a recommendation to resolve. I was cutting my pasture a while back, and I hit something that did a number on my brush hog. I have some gouges in the underside of the deck, blade bolts are stripped, blade pan bolt holes are worn, and...