Search results

Top link chain. I know a lot of people run them for their rotary cutters. What else do you use them on and do you have pictures of your set up? What are some precautions?

Here is a easy process to remove the blades or fins from Teks wood to metal screws.

For my shop(metal building) garage door the installer wants a wood frame around the opening. Which i will screw to the metal building. For studs I am going to use 2x12s on each side. The installer prefers I do not cut these and set the trim board on top of these studs as he doesn’t want a screw...

Question for the community. I just had a metal building from Caroline carport that I am going to insulate with 2” 4’x8’ foam board with foil on both sides. It will be enclosed with a garage door and a man door. Along the bottom i plan on putting up 4’x8’ plywood as to have a good wall for...

Kubota HST L 3901 2019 ~830 hours Yesterday i was moving dirt and it just shut off and through a E-20 error. I checked the Fuse and the “Main ECU (Ignition key)” fuse was popped. I replaced the fuse and moved the HST peddle to move Fwd. and the fuse popped again. Replaced fuse again And I was...

I have posted a few questions about my shop build and you guys have been really helpful! So my next question i have a 28x40 slab with 5 250’ runs of half inch pex. Is there a calc out there to figure out what size heating unit to put on it? I am think some form of water heater. If i am...

I am in the process of ordering my shop 28x40 and i am torn between getting 12”x12” frame out put in for fans. The intent of the fans is to pull the heat (and fumes) out of the shop during summer. However i do intend to heat the shop during winter. So then i would have to deal with the holes. I...

I am in the planning stages of a shop build 30x40 12’ high side walls. Metal building on slab with 12x12’ door, One walkindoor and two 12”x12” window frame outs in the gables for fans. And i plan to insulate. I live in East Tennessee and i am looking for suggestions on heating. My first...

I have a L3901 ~3 years old 700 hours. I have about 2 years worth of payments left on it. third function Rear hydraulic hookup Bucket Forks Grapple Bh77 backhoe Land pride box blade Land pride bushhog Grader blade most of those 700 hours are from backhoe work pulling down hill side and moving...

I have reclaimed wood from a old plat board house that was falling apart that i took down last winter. (Think old barn with newspaper insulation about to fall over) i am hoping to use the lumber as trim to put into my house. I heard you can use 20 mule team borax laundry detergent to treat for...

Anyone have any experience with one of these? At first it seems like a good idea. Especially for clearing small trees. However after thinking about it it seems like you run a high risk of the trees coming down on top of you. Tree Shears

Passing this along I hope it helps someone.

Can someone explain to me why they would be cutting in these conditions?

So…… the right tool for the job! Fun with chainsaws

Soo lets have a little fun again. Lets see how many things you can find wrong in this video. Fun with Chainsaws again. As a bonus one in fire

Soo lets have a little fun. Lets see how many things you can find wrong in this video. Fun with chainsaw

So QQ i have a Husqvarna weed eater that is not worth fixing. Its a 132R straight shaft model. I was looking to repurpose the shaft into a walking stick since i am going to ebay the good parts. There appears to be some bushings down the shaft but i am unfamiliar with how to remove them. Does...

Here is a DIY Starlink Temporary non-penetrating roof option mount that is cheap (almost free) and easy to move around. While trying to find a mounting spot on my roof that give me the best signal, this is what i came up with. I hope this helps someone. #Startlink #StarlinkMusk #SpaceX

Here are two videos where I show the seat Mod I did to give more leg room. Plus I now have a vertical angle adjustment using the PTO. Part 1 Part 2 Kubota BH77 seat bracket modification Results. MORE leg room. Part 2 (3) - YouTube Let me know what you think.

Hey everyone I am new here. I just purchased a L3901 loader and backhoe BH77, The backhoe control arms were to short. So here is a little video showing the longer control arms installed and differences.