Search results

Well I had a stuck rear brake and had to tap on the brake arm under the foot rest. Once I freed up the brake the tractor would not move in any gear. I put it in 4X4 and it moves real good. The front end in pulling tractor. When I put it in 2 wheel drive I can get it to move if I push on the...

I have a good condition JD 750 head with valves, springs, and Pre-combustion chambers installed for sale. Would like $200 to $300 for it. If anyone is intested I can post all numbers on the head. 3 Cylinders no cracks Bought it because seller said it was for a Yanmar 3T80 engine. It is not...

I have a good condition JD 750 head with valves, springs, and Pre-combustion chambers installed for sale. Would like $200 to $300 for it. If anyone is intested I can post all numbers on the head. 3 Cylinders no cracks Bought it because seller said it was for a Yanmar 3T80 engine. It is not...

Did some plowing last weekend..or at least tried. Got about 3 acres done with a 14 inch 2 bottom plow. Everything was working great then I went to an area that has HEAVY SOD and I mean HEAVY. Its a moist area and the grass/whatever is so thick you cannot even use a shovel to get to dirt...

I have been getting alot of private requests for turbo recommendations. I will post my thoughts: 1) There are only 2 MFGs that I know of that produce turbos small enough for diesel engines in the 110 Cubic inch/40 hp and less displacements... 2) They are MHI(Mitsibushi) and IHI. 3) My...

Well its been over 6 months with my MHI TD02 turbo installed on my 2610D. Did alot of snow blowing and tilling with it installed and things have been great. At my 8000 ft of elevation I have had to deal with derated engines constantly... My back up 5KW generator is only a 3.4KW real life...

Well, my 2610D has been working out great! The turbo I added is a great addition to the tractor. Here at 8000 feet of elevation while using my 5.5 foot Lorenze snowblower everything is flawless!! Tractor starts with out ANY assistance at temps down to 10 degrees F. I do however use the...

Was wondering if altitude can affect the radiator cap performance. I am at 8000 feet and water boils at 195 degree F here. Not sure how my antifreeze and water mixture is affected. Air pressure here is about 11 psi vs the 14.7 at sea level. Can I also assume water freezes at a lower temp...

Did some rototilling last weekend and was somewhat confused about my fuel tank and what it did. I was under the impression that the injection pump is gravity fed on my 2610D. But after about an hour in 70 degree weather of tilling I noticed my red fuel cap was about 3 to 4 inches LOWER than...

Could someone tell me where this is located? I have be advised that I could have a malfunctioning one. I have a clicking/thumping sound when raising loader and curling bucket. No clicking sound when lowering bucket or uncurling bucket. Also happens when raising 3pt. Thanks Rock

I just had to post this. My new John Deere Manual is a GREAT!!! To bleed fuel injection system on a 3 cylinder Yanmar motor. 1) Open fuel at filter 2) Open the 2 bleed screws on filter housing until no air bubbles 3) Close bleed screws on filter housing 4) Loosen injection pump valves on #1...

Got the remanufactured head from fredricks today. Here are some photos. Not sure what the silver thingie is.

Just got my John Deere manual for my YM2610D. Manual is for an 850 JD and it is GREATTT!!! Here is the process it describes for my tractor. 1)Shut off fuel and disconnect #1 injector line from pump 2)Unscrew delivery valve holder from pump and remove spring and delivery valve 3)Reinstall...

My manual for a 336 states that after the gov. linkage is disconnected, all you have to do is push the control rack to left and pull your pump. Pushing rack to left is supposed to give the nipple room to clear block. This was not the case for my tractor. I had to remove the two studs that...

Well here is the scoop. Decided to adjust valves and noticed right away that the only cylinder that was any good was #3. I could spin motor over by the fan until cylinder #3 started compression stroke and I had to push down on valve spring to release pressure and finish adjusting valves. Did...

I have posted a photo of my crank pull timing marks.. My manual has a photo too but photo is black and I cannot see anything. I need help to determine which mark my 3T80 engine injector pump is supposed to pop the #1 injector at. Right now injector #1 pops at where the number 1 is stamped on...

I would like to get everyone's opinion on a hydraulic issue I have. Background: about 2 months ago I started my tractor and after a short warm up began some loader work. Noticed the tractor was low on power but just thought it need to warm up some more. After about 10 minutes I saw the...

Just had to post some observations and experiences with this oil. 1st let me say I do use this product in my Yanmar tractor. It had 1300 hours on it when I put the cleaner in and then replaced the dino oil with the synthetic. Have 1350 or so hours on it now and no leaks observed. My turbo...

Due to my elevation (8000 ft) I am turbocharging my YM 2610D. Already have a turbo on it but it is too big. Finally found a MHI TD025M out of a 90 CID kubota. I will be installing it this weekend. I will document my progress as I go. So here is a photo of my tiny little turbocharger.

Did some cross referencing and purchased some new oil filters for my 2610D. Here is what I have found. Wix 51568 fit my tractor! Also I have confirmed that NAPA 1568 fits also ($12), STP S2802 fits ($3.49), Moble M1-104 fits ($9). Also, (UNCONFIRMED) Fram PH 5046, AC Delco PF1051, CARQUEST...

Can anyone tell me if this will work? I have a compression tester that goes to 300 psi. I have been able to screw the end of the compression tester into the fuel intake port of one of my old injectors. If I remove the needle in the old injector will that work? Or should I remove the entire...

Does anyone know if ANY company/mfg can make or does make a cab for a 2610D Yanmar? Blowing snow in the mountains with 50mph winds can get real cold with out one. How about a cab for a 750, 850 or 1050 JD. I could make one of those work I think???

2610D 3T80D engine 3 Cylinder 1.297 Liter displacement. Do not know factory Compression Ratio, probably 21:1 like the 336D. If anyone knows for sure, I would appriciate the info. I put a Tripple K (KO3) turbo on this tractor. Its too big for turbocharging most of our tractors but in my High...

Wanted to post the process i used to pull my injectors. 1) removed lines, clamps and return orfices 2) tried to pull up on injectors DID not WORK!! 3) blew out crevices with air and soaked with PB Blaster every day for a week 4) still would not come out, tapped with hammer still no go 5)...

Trying to time my tractor correctly. With clear hose attached to #1 injector line I find that my pump timing must be off. There are a total of 6 lines/marks on my crank pully. 3 of the lines/marks on my pully have #1,#2, and #3 right next to them. The other 3 lines are about 1 inch ahead of...

I purchased a used 2610D and when I got it the front left knuckle seal was leaking. So, I decided to replace all seals and bearings in the front end. 1st order of buisness was to purchase an owners manual, a parts manual, and a service manual. Once that was done I decided to purchase oil...