Search results

Hey All, Anybody run chains on a L2501 with R4's and no spacers?

So I have a 2021 L2501 with Loader. I opted out of the factory 3rd function at the time of purchase to reduce the cost. My plan was to install a aftermarket 3rd function myself, I see many options for the electrically operated ones. Have any of you installed manual "spool" valves? It seems...

Hey All, Anybody have insight on a Ford 5500 Backhoe hydraulic fitting? I blew my boom lift line. One end appears to be JIC 12 Female and the other JIC 14 Female. The 14 size seem to be an oddball. Unfortunately i'm up North and those that fix this stuff know less than I do, so I need to...

Hello All, I have been the owner of my JM254 new since 2007. I now have 500 hrs on it. I have had little issues and none that have needed research lately. My new problem is with the shuttle shift. I have adjusted it many times because it wouldn't engage in one of the directions with success...

will the oil from the axle housing run into the portal? this is after removing to change a short axle/hub thanks

Hi all, I have a JM254 with shuttle. Does anyone have the shift adjust procedure. I have a hard time going into gear.

Hi all, I am looking into this for a friend. Does anybody know if Jang Dong has a one cylinder engine? It's a diesel. Apparently it's a 2007 around 20 horse. Any other brand names that a fellow could look for parts under. I don't know much about it. Main thing is finding info about the 1...

Just for reference, digging with LW-06 jinma backhoe. They work.

Does anybody have any info on adjusting the fuel output on these pumps?

So I was pulling backwards in 4x4 with the bucket about 2 feet of the ground. I needed the lift to try and get the load moving. 3-4thousand pounds of concrete Hardie board siding on pallets. It wasn't moving but I tried again.....and bang. Sound came from the left front, I seen dust come of the...

Hey All, So while trying to engage backhoe pump PTO it when pop crunch grind and now there is no discernable position and no function. So the question is do you have to pull the the hydraulic lift mechanism/tank off. And has anybody done this type of fix? What level does the tractor have to...

jinma254 Burned Pump Failed? Little Help? Ok So, Jinma 254LE main tractor pump/gear type. So I started her up on boxing day and let the tractor warm up. However I put her on high idle fairly soon (cold oil). When I came to move the tractor 1/2 hour later there were no hydraulics nothing. The...

Little Help? Ok So, Jinma 254LE main tractor pump/gear type. So I started her up on boxing day and let the tractor warm up. However I put her on high idle fairly soon (cold oil). When I came to move the tractor 1/2 hour later there were no hydraulics nothing. The pump was hot to the touch...

Hey Guys, Gonna build a BB, and was wondering if the blade edge is below the side plate edges? As in if it here it would cut more? Or is it just flush? Thanks

Good Day, I'm thinking of using 1"-1 1/4" solid stock steel, then cutting 8-10" inch lenghths at an angle (for the tooth point) then hard surfacing the point edges, then welding solid to the bucket. Any ideas. I already decided that solid mount would be ok. I don't need to take them off....i...

Hi guys, Has anyone run straight ATF fluid in a 2007 JM254? Im in the Yukon we are -20 celsius dipping into the 30's. Im really getting peeved at even AW32. My hydrolics are in slow motion at best. Will ATF wreck pumps or rams?

Hello, I have a 07 JM254, so far I have about 40hrs on it. Since I have had it the 3pt has not worked the only time that it lifts is if I raise the loader and hold the lift valve on the 3 pt open then lower the loader. Any ideas what the problem could be?

hi guys, I am trying to figure the GPM of my LW-6 backhoe pump. It is marked 10ml per revolution now if I knew the rpm of the shaft I could do the math. Assuming the PTO was at 540rpm what would the bh pump be turning at and at 1000rpm respectively? Or if anyone knows that would be great...

Hi guys, Maybe you can help, if you look at your hand control valve from the right side of the tractor there are four line exiting out the bottom then to the emediate left of that there is a set bolt with a lock nut on it. What does this little feller do. And what is its home position. Because...

Hi all, Im having a few problems with my 3 point. How do you engage the hydraulics for the 3 point? Also what are the two ( left and right ) quick connects at the back near the 3 point? The reason I ask is because I didn't get my pump with my Jinma backhoe? Thanks

Hi Guys, Mine was unscrewed almost to the point of falling out, and leaking diesel. My machine is a brand new JM254. What is this for, does anybody know of a good reference for these injector pumps?

Hi, Could someone tell me what the eye to eye/top to bottom dimension is on a CAT 1 hitch? I want to make a grader attachement for mine but I don't have any attachements yet to look at. Thanks

Hello All, Well i just made my first purchase. A JM254 2WD with a FEL and BH. I am importing it myself direct from China. So I'll see if it actually get here!! But otherwise I am very happy with my decission. For now it will be used for landscaping my new, heavily treed lot and snow removal...