Search results

I walked into a very large Kubota dealer today, go to the parts counter and tell them I need enough SUTD to do a complete change on my M9540, plus two filters. They can't tell me how much I need and I need to consult my owners manual.

I have a slow leak in my right front tire on my M9540. Tried finding it with soap and water and had no luck, so I did what any country boy would do and drove into the creek. Turns out it is at a weld point on the rim. I'm thinking that taking off the tire and welding from the inside would br the...

The tractor end of the PTO shaft for my bush hog has a slip ring against a spring that holds three steel balls in place to secure the shaft to the tractor. It goes on and the ring snaps in place, but comes off in operation. has anyone ran into this problem and did you find a fix? I'm thinking of...

I've looked at his both ways and wondered what you guys think? Should I lay the floor tile first and then install the cabinets or install the cabinets first. I'm leaning toward doing the tile first seeing as it it 18"x18" travertine. Cary

I have a M9540 and it appears that I need to adjust the hydraulic shuttle cables, also I have been told to remove the lower boots on the cables. Has anyone dealt with these issues and any advise would be welcomed. Cary

Need help from the plumbers and others. I'm ready to hire a plumber for the house we are building. I'm real pleased with one candidate, but he runs the supply lines from the crawl space to sinks, etc through the floor instead of in the wall. His point of being able to fix potential problems in...

Looking at getting one of those contractor series forced air portable heaters to use in the barn. Could use some input on kerosene vs propane. Both look costly to run, but we have the need. Cary

Has anyone dealt with this company? Unlimited Fabrication, LLC PO BOX 454 Denton, NC 27239 Skid Steer loader attachments Thier products look good and the pricing seems fair. Bake

I had a flat on my horse trailer so I attempted to air it up. I soon realized that I was not gaining much. I pulled the tire and discovered the tread seperated on the inside wall. I do a web search and discover that there has been issues with Goodyear Wrangler load range E. I keep hearing of...

I bought a 3pt post driver to use on my M9450. I have two sets of remotes. The top set detents in the forward position and is spring return to the rear. The bottom set of remotes detents both ways. I was told to hook up the supply line to a remote that detents and this would give me a hydraulic...

I bought a 3pt post driver to use on my M9450. I have two sets of remotes. The top set detents in the forward position and is spring return to the rear. The bottom set of remotes detents both ways. I was told to hook up the supply line to a remote that detents and this would give me a hydraulic...

I bought a new post hole digger and sure am going through shear pins/bolts. The grade two that came with it were a real joke, they advertize a five year gear box warrenty, well with those bolts it would last forever. I went with grade five and even with the RPMs low and babying the dig, I,m...

I need to buy a canopy for my tractor, Kubota M9540, any advice on this purchase would be appreciated. Bake

Here is a picture of the new tractr taken last week in Kentucky.

Finally made a deal on a new tractor for my new farm. I thought buying a tractor would be a "fun" experience, boy was I wrong. It seems that tractor dealers in general rate right up there with lawyers, car salesman, realtors, etc. Most of them acted like you were bothering them when you would...

It appears that there is quite an increase in the gpm of the 500 series hydraulics over the 400 series. Does anyone have input on loader operation good or bad on the 471 through 491 units? Thanks, Bake

Hello, I will be moving to south central Kentucky and would like dealer recommendations for Kentucky and Tennessee. I'm looking at Deere, CaseIH, Kubota and Massey Fergussion. I need a minimum 60 PTO hp, 4wd and a loader. Thanks, Cary