Search results

I have a NH 1715 with a loader on it. It has turf tires. How many pounds of fluid should I put in the rear tires?

Hey all, I am having a problem with the bucket roll bleeding off. I had a cylinder leaking and thought that may be the problem. I had it rebuilt and it is doing the same thing. Would it be the joystick control leaking off? If so, how hard is it to rebuild? 1715 Ford Factory FEL

Hey all, It is time for me to replace the clutch on my 1715 tractor. messicks.com has all the parts in stock. But I can not find the gauge for setting it. The manual refers to #FNH 1300 as the correct gauge. Where can I get one at? I watched this video of a guy doing a replacement. He didn't...

I am in the market for a new trailer. Wanting a 20-22' partial tilt. 14k. Below is what i have found close to me 2017 Maxxd G6X 8322. 14k 14' tilt, 6' stationary. $4900 2018 CornPro UT-21. 14k 17' tilt 4' stationary $5750 2018 Sure-trac 7 x 18 + 4. 14k 18'tilt 4'stationary $6200 2019 PJ 20'...

I am wanting to put a solar battery tender on my dump trailer. Any suggestions of what to get? I was looking at Battery Tender 021-1163 5W Solar Maintainer Amazon.com: Battery Tender 21-1163 5W Solar Maintainer: Automotive

I am needing to replace the clutch in my Ford 1715 tractor. I have the service manual supplement pictured, but am needing Manual #40132030. It is the 13, 15, and 1720 Repair Manual. Anyone have a copy or know where to find one? SERIAL. UK30757 MODEL. AK412T UNIT. 7C13B ENGINE...

My dad's 4320 ag tractor is getting water in the oil. Not a lot but It is there. It is a 1972 I believe. Are there any places to start looking? Something that is very common problem with this tractor? Also, does this have sleeved cylinders that may have a leaking o ring? Thanks Bill

I am in the market for a 12 or 14 foot dump trailer. It will be used for hauling brush, mulch, maybe some rock, and a few roofing jobs. In your opinion, what type lift do you suggest? The closest dealers to me have PJ, Big Tex, Lamar, Load Trail, Iron Bull, Corn Pro. Also, what brand...

A friend of mine has a IH2424 industrial tractor with a backhoe on it. All of a sudden he is not able to shift into 2nd or 3rd. He says he can't even find the notch for them. Any clues as to where to start? Could he pull the shifter rod to look inside or is there a ball on the end of it that...

I was mowing today when the right hand drive started to whine and not want to pull itself. If i would stop for 10 minute or so it would work fine for a bit then start it again. Any suggestions on where to start? Are the drives serviceable or not? Ariens EZR1648 model 915009 thanks Bill

Hey all, I am the original owner of a EZR1648. I think it is the 1st or 2nd year model that came out. Anyways, Here lately it ain't been mowing very well. Don't cut the grass, just knocks it down. or leaves strips on the outside edges of the blades, like they ain't turning fast enough. I...

I have a 1715 with about 900 hrs on it. Here lately the hydraulics have been slow, they wine, and are real jerky. I thought I would change the fluid today to see if that helps, since it was real milky. Parts store did not have a new filter so I reused old one. This did no good. Same problem...

I am needing some help with a New Holland round bale monitor. It is model number 86624228. It is suppose to buzz when the bale is large enough and ready to tie. The problem is that the buzzer isn't loud enough. Has anyone ever added a light to this that would flash? Or a car horn?

Here are some pictures of my truck mounted snow plow I converted over to a FEL mounted one. Now I need to get the wire wheel out. Clean it up and paint it blue.

I am looking for a 7308 FEL manual and the parts list. Send me a PM with a email address if you have one. Thanks Bill

I have a 1715 with FEL. I am taking the front bucket off and mounting a truck style snow blade to the FEL arms. I am using the roll part of the lift to operate the angle. Now to the question. I pulled the hydro hose from the bucket and got a real milky looking fluid (water in it I am sure). I...

I am needing a 5' 3 point tiller. Are there any grey market dealers in southern Illinois. I live close to Effingham Thanks Bill