Search results

I just evidently cracked the hydraulic filter block on my 4046 for the second time in six months .anyone else do this? I was running over some brush both times. Nothing big. I think I could fix it myself if I knew the part number Fluid is pouring out above filter. The filter points...

Have a new harbor freight near me now, they have their quick hitch for $99.00 and a 25% coupon tomorrow only and my daughter gave me a $25.00 gift card for HF. Any thought on how that would work on my XR4046? I have a Rhino SE60 cutter and a box blade that give me the most pain trying to...

I have a three point carry all and I am using it for a boomless sprayer.I put two fifty five gallon drums on it and a 12 volt pump and it works fine. If it is setting on the ground and I hook up, by the time I raise the platform to the height I want. The back is pointing downward at a severe...

Somehow I bent the right step on my XR4046H, not just bent, folded it flat.:( I almost never use the right step, and was wondering about replacing it with a tool box or something. I am afraid to call the dealer and find out how much a new step cost... Any ideas??

I have a 135 gas Continental and have worked on the fuel lines several times and would like to replace them with braided steel lines. As close as that fuel line runs to the muffler and exhaust manifold is that safe? The original steel rusted out, I made new ones out of copper. Somewhere...

My wife's uncle loaned me his Howse 10' three point hitch cutter 4 years ago and said I could use it if I wanted to fix the slip clutch. So I did,put new fiber discs in it etc. I got to use it about 2 hours and he said he needed it. Lately he said he had loaned it out and it wasn't working...

Is there a switched 12 volt source under the dash of a XR4046H? I am going to install a camera on the front grille so I can see what I am doing. Haven't found a available 12 volt lead up there. I know there is a pair unused, on the rops. But I was trying to stay toward the front. Thanks

I have a piece of shiny aluminum diamond plate. I think it would make a good insert for the grille guard, but concerned it might cut down on air flow. I need to get something in there before I run a limb thru my grille.

Is there an accessory that fits in the long slots in the grill guard? It seems like a lot of open space for a limb to get through and do some serious damage. I'm thinking about trying to mount a camera somewhere on the front so I can see my forks and grapple better also.

I bought a Tomahawk stump bucket for my 4046 yesterday and tried it out this morning on a big stump in the front yard . I didnt really think it would do it, I was pleasantly surprised. Had it out of the ground in 10 or 15 minutes. I actually got it to get rid of some saplings I let get out of...

My nephew works for a crop farmer and I asked him to get me some bulk corn. He said the bags held about 2000 pounds. I told him to try to keep them around 1500 pounds each. He forgot to tell the owner and he filled them up. Am I going to be able to handle them with my XR4046? I bought...

I have a 1967 mf135 z145 continental. Having trouble getting the starter to turn over. Kept messing with the wires and after a while it would start. today it wouldn't start. I went back with all kind of tools and meter etc. I noticed when I turned the key on ,a long spark would jump from the...

Was using the tractor yesterday and two orange lights came on the dash. I got the owners manual and think I now know less than I thought I knew before. One had a temperature sign on it and the other looked like a turbo exhaust with back slashes across it, does that mean it is running in the...

My other diesel tractor needs to sit and idle for a few minutes if running hard before you kill the engine,been told to do that so the turbo doesn't gunk up. Is this the same? Wasn't expecting this one to just shut off with the key. My parking brake only beeps 4or 5 times when I get off either...

I hope I haven't stepped into a bunch of gun hating folks who will run me off, but I would like to put a rifle rack on the rop of my 4046H. Any suggestions? Probably will want to carry my AR-15 or .223 bolt action. I need to thin the coyote population and I see them a lot when I'm on the...

I just changed my profile, they delivered my tractor this morning. I drove it in a circle around the yard and had to go back to the office. Called the insurance co. on they way back and got it covered.

Does the 4046 have a switch for a rear work light? Or does it come with one? Never mind, I called Magees and he said it came with a work light. I agree with Mr Whispering Oak Farm, anyone around the se missouri, ne missouri should check with Doug Jackson, or Mark at Magees.

How many of you use fluid in your LS tractor tires? I have to have it in my 135 Massey or I can't do anything. I buy methanol at tire shop, dilute it and pump it in myself. I don't know where to get beet juice and if it has any advantage. Any thoughts? Methanol should be harmless to the...

I have a 67 MF135 and a mf2705 , and really need a tractor with a loader. Getting old is not as much fun as it is made out to be... I need to put out 4x5 hay bales and clean out barn move brush etc. I sat on a 3039 and it felt to small for me. I am selling about twenty acres of timber to...

My son in law has his grandpa's 2460 long tractor. Hasn't seen maintenance in a long time. I am trying to help him. One thing is it is very uncomfortable to ride. The seat pitches forward and your butt is alway trying to slide out. I can't figure out how to make it lean back. At first...

I am putting a new water pump and pulley on my 67 135 continental, what holds pulley on the pump shaft? I thought there was a c clip but I don't see one. Thanks

Does anyone have a picture of the wiring on the starter solenoid and oil pressure switch on a 1978 massey 2705 Calves got to my wiring the other day, and I can't figure out where they go back. I have five wires off. I have a parts manual and a IT manual but can't find anything usefull. Thanks Dan

Has any one put a aftermarket seat on their 135? Right now I'm just sitting on the pan, not very comfortable. My dad put a aftermarket on his and I don't like it. It is too high and I feel off balance. My tractor has the old curved piece of steel for a bracket, but his had the fancy coil spring...

My 135 has quit lifting a heavy load. It will pick the arms all the way up empy, but with a bale of hay it rises very slowly and only about a foot. If I remove the inspection plate on the right and move the position lever upward the vertical lever will only move the pump lever (the one with the...

I'm not sure what the proper name of what I need is, so I hope someone can fill me in. I just bought a 2705 and the left cylinder that controls the lift arm is leaking sort of like a sieve. The local massey dealer just went under, in fact the are auctioning off what is left tomorrow, so I don't...