Search results

Just bought a MF 254 but it has no 3 point lift bars, I have the vertical adjustable bars but not the low long ones. What is the dimension form eye to eye on these bars? Was thinking of making my own, assume steel 50 or mid grade will do on this. Appreciate the help on this need lengt end end...

Had a stuck clutch on my 5200, cleaned all up,but now I need to adjust the fingers for the traction and pto. I can't find The gauge tools jdg 826-7-8 online, does anybody know the finger height? Thanks

My starter on my to30 needs new brushes some are broken. See picture. Does anybody have an idea where you van buy them? Thanks for your help!

I have a problem with my jd 4700, even when the rpm is idling most of the time it has a hard time to shifting in and out of neutral, the shift handle feels like it flexes and I have to push the forwards pedal just a bid to get it to shift , any ideas on this? Also even when idling it has the...

When I use my fel valve to the right so empthy the bucket on my jd 4700 and on my 990 there is a point that both sides get oil. I noticed when I was using a tree sheer with a 4" cylinder, small return od rod, on the ram, the cyliner first closes, but then opens after I mover the handle all...

I just got a used JD 4700 with 16.9x20 and 10- 15 , rim front tires, both sets turf tires. I want to replace them with either R4 pr R 1 tires., probably 16.9x 24 R 1 on the back and 10- 16.5 rim, or 16" rim or 15" rim on the front. am i restricted on the diameter of the tires and rims on...

I spayed my jd 990 with a water hose, also on inside of the hood agains the dash. The tractor would not start anymore., waited one day 90 degrees and dry, Houston, no change, thought is was the battery which was 4.5 years old, changed it, found a bad connecters on positive side fixed all that...

My tn 65 has a squealing sound, this started after I changed all the filters and hydraulic oil. It mostly only appears after I use the steering, then when I stop steering 10-20 seconds later the squealing stops as well. I loosened the pressure line from the steering pump and notice foaming oil...

just off loaded my "new" 2003 tn 65, when i stepped on the tractor i lifted to steering wheel, (to brace myself) about 1/2" now it wont steer anymore, the wheel turns freely and it looks like the shaft is disconnected of the valve! any suggestion how to fix this? pete

I want to convert my L7300 phd into a hydraulic one which will hook to my jd5310 fel. I have a hydraulic motor brand Char-lynn 101 1025-009 with 12-14 gpm flow delivering 650-876inch/lbs torque Does anybody have an idea if this motor gives enough torque and speed to run the post hole digger? JD...

I just bought an used Leinbach 7300, for a good price but the tractor end of the pto shaft was missing. I checked on line and believe the shaft is a Bondioli & Pavesi 36.6mm o.d. lemon shape. I tried to look for a replacement outside shaft (should be tube 12516) but so far i am unsuccessful...

I have a 5310 JD, just resently the temperature gauge and the tank gauge are showing hot in the red and completely full , over the full mark, as soon as i turn the ignition swith and start the engine, they both are off, they do do come back to cold end empthy. do i have a sensor problem or a...

I own a 5310 jd with front end loader and am looking for a hydraulic brush cutter with open end, to put on the front end loader. The only ones i find on line are for skid steer loaders and need a minimum 16gpm. (5-6ft wide) Does anybody have experience with a low gpm hydraulic cutters? Are they...

I want to add a root grapple to my 990 johndeere front end loader, does anybody has experience with a scv multiplier valve?

I just bough a 5310 JD with front end loader. I wan to use my backhoe behind this one, what is the best (most cost effective way) to install power beyond on the 5310?