Search results

Results 1 to 27 of 27
  1. A

    Help getting lower draft link pin out

    Just had the same thing happen to my JD 4700. Same deal, pin wouldn't come out. It was getting hung up on the backhoe mount. I took a grinder to the old pin base and got it out in 10 minutes. I was careful not to grind too deep. Now time to buy a $120 pin!!!!
  2. A

    Bent bucket cyl on model 48 backhoe

    Are your measurements from end to end of the cross tubes. Or from the center of one cross tube pin, to the center of the other cross tube pin? Thanks again Al Hopefully, I will have this thing running again soon!
  3. A

    Bent bucket cyl on model 48 backhoe

    👍
  4. A

    Bent bucket cyl on model 48 backhoe

    I purchased a 1.25 “ x 8” piece of stock steel and some bushings. I’m not sure if I’m going to use the original bolt hole to hold the pin. When the new cylinder is in place I can determine if I need any shims
  5. A

    Bent bucket cyl on model 48 backhoe

  6. A

    Bent bucket cyl on model 48 backhoe

    Thanks for the measurements. My new cylinder is scheduled to arrive today. I removed the old cylinder & pins the other day with no difficulties. The pins came out with minimal effort. Hopefully I can get it to the welder tomorrow. Thanks Al
  7. A

    Bent bucket cyl on model 48 backhoe

    My JD 4700 with 48 backhoe is all factory
  8. A

    Bent bucket cyl on model 48 backhoe

    This is my first time repairing a hydraulic cylinder (besides replacing hoses). Two questions 1)What did you use to cut the rod? Metal chop saw ? 2) Also, guessing I'm going to to be cutting somewhere between 6-8 inches of the replacement rod off. Prior to cutting it, I'm figuring...
  9. A

    Bent bucket cyl on model 48 backhoe

    I just had the same thing happen to my bucket. Bent the dam rod! I was reading your post .I think I am interested in going in the same direction. One quick question. Instead of putting bushings on the one end, why didn’t you replace that end of the new cylinder with the end from the original...
  10. A

    Pole Chainsaws

    I just ordered a RedMax pole saw. They have excellent reviews. I will let everyone know how it performs when I get it in the next few days. Al
  11. A

    Jut bought a new/used Aluminum H&H Speed loader tilt trailer

    👍
  12. A

    Jut bought a new/used Aluminum H&H Speed loader tilt trailer

    I purchased a used (new to me) H&H electric speed loader tilt trailer. 20ft, 10k , 10k Winch. brand new radial trailer tires. It seems like a solid unit, I plan on using it for my John Deere 4700 loader/backhoe. Here are a few pics
  13. A

    Trailer needed for JD 4700 question

    I have a John Deere 4700, 460 loader, 48 backhoe. Altogether, it weighs just over 6000 lbs according to my estimates I am looking for a 10k lb trailer to transport my JD a tractor a short distance from my house to a summer property. I am interested in a light weight aluminum trailer...
  14. A

    John Deere 4700 won't go into gear

    M808491. Pinion
  15. A

    John Deere 4700 won't go into gear

    Update I was at the tractor repair shop and they found the problem.
  16. A

    John Deere 4700 won't go into gear

    I looked underneath and didn’t see anything obvious. I’m taking it to the repair shop tomorrow.
  17. A

    John Deere 4700 won't go into gear

    I was using my JD 4700 Power Reverser today. However, when moving some wood I heard a "thud" or "clunk" and the tractor would not go in gear. After trying different gear ranges with no success, I put it in 4WD. The front tires moving and I was able to get it back to my house. Also, I had...
  18. A

    John Deere Power Reverser won't Start

    I have a 4700 too, most likely its the fuel pump solenoid. Take the solenoid off and clean it. Think about replacing it, it is a $30 part Al https://www.amazon.com/M810324-Stop-Solenoid-Made-Deere/dp/B019A6PRL6
  19. A

    John Deere 3320 w, 300CX loader - hydraulic requirements for grapple

    Do you have a pic of your winch installed?
  20. A

    What does this lever do?

    That makes sense. Thank you What is the difference if it is in the middle or in the unlock position? Thanks again AL
  21. A

    What does this lever do?

    Hello, I have a JD 4700 and I am trying to figure out what this lever does. The manual is calling it a “selective control lock lever”. However, after reading the manual, I still don’t understand what it does. The only implements on my tractor are a front end loader and a backhoe Thanks Al
  22. A

    Who make a good grappler? Need one for my 4700

    Pic
  23. A

    Who make a good grappler? Need one for my 4700

    I am in the market for a grappler for my JD 4700, 460 loader, 48 backhoe. I was looking at a 72” by Titan products. Are they any good? If someone can point me in the right direction it would be much appreciated. Also, I need to purchase a 3rd valve kit for the tractor. Again, I would...
  24. A

    What third valve kit do I need John Deere 4700

    Hello I want to put a grapple bucket on my John Deere 4700 Power Reverser. Currently I have a 460 loader and 48 back hoe on the unit. What 3r valve kit do I need ? Where is the best place to purchase it ? Thanks Al
  25. A

    FEL problem on my JD. Need help

    When I go to dump the bucket on my JD 4700 460 loader the lever sticks to the dump position and does not return to the middle"neutral". So the bucket continues to dump unless I move the lever back to the middle. Any idea why this is doing this??? When I go to raise or lower the bucket...
  26. A

    Any JD4700 owners here??

    Just bought a JD 4700. About 10 years old. Just curious if there are Any 4700 owners on this forum. If so any advice with this unit???? Thanks Al
  27. A

    Oil wt for jd 4700

    I bought a 10 year old jd 4700. What wt oil should I use? I live in north east pennsylvania Thanks. Al

Footer Links 1

Top