Search results

Offer?

If the 3 point arms could be left on the tractor at all the time, I would keep using them. The arms are removed to install the backhoe, and the Pat's makes the arms awkward and heavy to remove/install. Cleaning up the shop, filling the trash can every week.

$100 plus shipping. Shipping will be around $25

Any way to repair the damage to the rod? Could make a new rod if we knew how remove the piston from the rod. Does this come apart somehow?

Got this a while back for my MT125. Move on to the Land Pride quick hitch. The separator got a bit bent. $150 plus shipping to continental US. Has pins, no washers. Fits in large flat rate box. Ship weight is around 25 lbs.

I used 4 flush mount ceiling speakers in my 30x45 shop. Nice consistent volume level wherever I am working. No moving speakers around or annoying loudness when too close to the single speaker.

The single switch is the lever for the three point. and the triple switch is on the roll bar with a plastic zip tie for now. I will probably make a bracket to better mount the triple switch where it is now. If I had it to do over, a double switch on the three point lever would be better.

Added four rear remotes and a flail mower. Summit hydraulic kit with custom brackets.

We referred to that as "swap till you drop"

Sometimes it is drop shipping. For example Supply House sells Mr Cool parts, and the parts ship from Mr Cool. But the eBay/Amazon deal is fraud.

Some of that is arbitrage. List a product on eBay, if it sells buy it from Amazon and send as gift to eBay buyer.

Just under a 100 feet of 36-48 inch deep trench. In some parts of the trench the hardpan was tough to dig through. Trench is for a new electric service in 4:inch conduit. My small tractor was worked hard and performed well.

This? Or Here?

Twenty-nine of these just sold at Richie Brothers in Dunnigan CA. Around 5000 + tax and fees. I registered for the auction but missed it somehow. Probably best to miss as I do not need one anymore. Andy Link to Auction

Anyone have the MT125 service manual?

Can you post the relevant sections of the diagram? I looked at my tractor, without disassembly of the engine side cover and the dash, I can't see much.

You get your wiring figured out?

Free, anyone interested?

Took my cylinder to a local hydraulic shop after disassembly and cleaning. $30 for the all the seals and such. They measured the parts to figure out what was needed.

After cutting the tabs off of the bucket, non standard quick-tach brackets remain. On the bucket the vertical dimension is too short and the pin spacing is wrong. So off came the top brackets. Also spent some time cleaning up where the tabs used to be. Got the cross brace tacked in place.

Got it all clamped up and started welding it. Moving around to try and minimize distortion from heat.

Took a few tries to get this lined up. Photo is from first try. Left side is a bit twisted. Clamping the plates front to front, was able to use the square against the pins to set the height. The distance of the pins to the plate should be consistent due to the milling operation. Got a few...

After being inspired by this posting decided to give it a try. Ordered the quick attach set from Amazon. The plate was marked as Vevor brand. Spent some quality time with the angle grinder and cutoff wheels: Cleaning up the edges of the tabs that were cut off. These will be welded to the...

@mslisaj On your quick-tach, are these bushings still used, or are the side plates closer together? Looking at your photos, I do not see the bushings. Nevermind, I see in your last picture no large bushings.

I decided to go a different direction and ordered the weld on quick-tach adapters after being inspired by this post.

I have three lines back there and use three with the backhoe on. And only two are in use when the backhoe is off. I assume that the line which is only used with the backhoe is the return to tank line. Andy

I would like to loan my tractor to my neighbor, he really needs a tractor. But he is not a tractor person and I do not want him to hurt himself.

Ok this guy Taryl had a couple good videos about these transmissions. Makes me want to take mine apart. His videos take a bit of getting used to.

I have the LL1101 and it did not come with the SSQA. There are other threads on here that describe the factory quick hitch that comes with the MT125 as smaller than standard size. Post in thread 'Buying Advice - LS MT122' Buying Advice - LS MT122

I have been happy with this one, bit on the small side but quiet.

Can you provide the part numbers of what you got?

This?

I will order one also if we figure out it fits.

https://www.tractorbynet.com/forums/threads/is-mt125-new-loader-question.412064/ Last post here is interesting also

Does the 25S use the 100LC loader? If so then this.

What is the cost of just the SSQA part that mounts on the loader? Then I will mod my bucket to fit. My MT 125 is great also.

Crack in plastic around fuel fill.

Ductless air conditioner/heat pump.

Put the mini split on the bracket.

Anyone done this? Any pictures of the factory ones? I would like to add two remotes and at least the hydraulic top link. I do have the backhoe. I considered the quick hitch, but since the 3pt arms are removed to install the backhoe, the quick hitch would just be one more item to mess with...

Mine were just past finger tight. Snugged them up a bit. Thanks!

Thanks, I will check mine tomorrow.

I rented a Vermeer walk behind. Got rid of a very large fresh Eucalyptus and quite a few others. Four hour rental. But I ran it non stop. Sunbelt rental here gives you 8 hours on the meter for Friday-Monday at a one day charge. If you rent, get the one that drives around, not the one you have to...

Here is the link to the diagrams http://lspo.lsmtron.com/PartsList/wpc2000_MAIN.aspx

These help? HST is on the right.

76 Ford Torino

Here the price varies with the interest rate. They simply prepay interest and charge more for the tractor. MT125 with backhoe and loader: Quote 1 17,900 plus tax 60 months 1.99% 17,259 plus tax 60 months 2.??%

Took delivery of my new MT125 and backhoe.

I put electric brakes on my 6x12 single axle enclosed trailer. I already had the controller in my 1/2 ton truck. Did not cost much for the brakes, just bolted right on to my axles. Much nicer to pull and easier on the truck when stopping.

Have 2.5 Acres near Sacramento Ca. And looking into a small (under 25 hp) tractor.