Search results

ATF handles higher temps but other splitter components don't handle the higher temps as well.

135 degrees is perfect. This temperature helps reduce moisture. Above 160 many hydrualic fluids start to break down.

I would be more concerned about the spindles and bearings used on most consumer grade splitters. Without suspension they are derated by 50 percent.

Normally the return line should never exceed 20 PSI unless there is a obstruction in the line.

For the return line you do not need hydraulic high pressure hose , only oil compatible hose.

If the engine came with a built-in fuel tank it most likely is a duel fuel engine. Look up the model and serial numbers for engine specs.

Impluse sprinklers have a minimum pressure and flow needed to operate properly. Ha the same problem. I have both city and well water available my impluse sprinklers would not function properly with the well, when switched to the cityhose bib the sprinklers worked as they sould.

I have made inserts for two trailers I have for hauling brush and leaves. The pole can telescope and winch receiver will accept either manual or electric winches.

Check the seat safety switch.

On hard surfaces after first pass to get the majority of the leaves make a second pass with the mower deck shut off. The spinning blades cause the leaves to blow out the side on hard pavement.

With the 6.5 hp engine a 11 gpm pump would be standard. Generally the pumps used on splitters are not rebuildable due to lack of replacement parts.

I needed a trailer that could transport my ATV an also go anywhere thru the woods that the ATV could go.

The handle can be set to operate in different directions

The valves pictured in previous posts differ as to the work port functions. On the Energy style valves the work port nearest the handle controls the retract of the cylinder. On the Prince style valves the work port nearest the handle controls the extend of the cylinder.

The cost to produce a barrel of oil at the well head has changed little week to week or even year to year. When the price per barrel goes up profits soar. With all these so-called shortages investors profits keep growing at a faster than normal rate.

I have used these traps and found them to be the most effective of all I tried.

Proper shackle spacing per axle manufacturer. http://www.dexterpartsonline.com/files/2036913/uploaded/Leaf%20Spring%20Information.pdf

The trailer springs may have been replaced with shorter springs. Trailer springs come in various lengths. The correct position is shown in post #4.

The pump appears to be 2-stage. A single stage pump will not have the check valve and unloading plugs. The most common gpm for these pumps are 11 and 16 gallon models. Measure the length to get a basic idea of gpm.

Menards carries galvanized carriage bolts and nuts.

When ordering replacement primer bulbs you must check for ethanol compatibility.

A return filter should never have pressure greater than 25 psi that would cause the filter to burst unless there is blockage. The common cause of blockage in a return filter is a damaged filter head by-pass valve. This valve is made of plastic and when it breaks it can obstruct the pipe to the...

The basic way to size hose for a hydraulic pump is to match pump outlet size minimum or one size larger. Also check hydraulic fitting as some styles or brands are restrictive.

Some of the old chargers are for charging NiCad batteries only.

When using cutoff wheels I found that they don't work well if you try to use them like a saw, where you cut all the way thru as you move forward. When cuts of more than a few inches need to be made I place a metal straight edge where a line is scored. Then with light pressure and moving back and...

Generally the return pipe enters the top of the tank then extends to near the tank bottom where the fluid is discharged.

This would be the minimum return filter you would want. 3/4" NPT 25 GPM Zinga Return Line Filter 25 PSI Bypass Zinga ZAF-07-25-0-10

All filters and strainers used should be rated double the pump capacity, to prevent cavitation with suction filters and bypassing with return filters.

I made one to load my sons bike.

I use a small receiver mount. 1 1/4" tube for winch base and 1 1/2" -1/8" wall tube for the receiver. The first pic is of a trailer tounge mount. The second pic is a mount for the front of another trailer. Last pic is the winch on a log splitter lift.

The least costly method for a log lift attachment is to use a electric winch. This one is self supported. 100 0123 - YouTube Here is a pic of a attached electric lift.