This should be very straightforward however I cannot get the mechanical stop to move in the right position. The joystick will allow the hydraulics to tilt the bucket back and forth. Somehow the mechanical stop is not allowing me to raise or lower the front and loader. What am I doing wrong? I...
I started this post with a tractor that would not turn over. The
reason that it would not turn over was because the bell housing
was half full of water (at least 1/2 gallon). The starter solenoid
was shot. I rebuilt the starter and bought a new solenoid. The tractor
will start and run fine...
First I must say I have not figured out how to change my profile. I have a kioti dk40se with around 60 hours. This is a shuttle shift with a loader. This tractor is stored in a insulated building with cement floor. I have not started it for about three weeks. I went to start it and only get a...
I have read many posts here about electrical issues. Most are ground related. I suspect mine is the same. I suspected a bad key switch at first. I have ruled that out. My trouble is #5 (amp meter)at the key switch. When I move the key to any other position besides off I loose power to wire #5. I...
Jinma 224 4x4 with power steering.I know there is not supposed to be fluid in the column. There is a weep hole in the base of the column. After running the tractor for awhile hydraulic fliid will start comming out of the weep hole. The only post I could find regarding this matter was a guy that...
I have a Jinma 224 with about 600 hrs on it. I was mowing last Sunday for around two hours. I stopped to eat lunch, then tried to start the tractor. The 30 amp main fuse was blown. I was out in a field so I started it with a screw driver at the starter solenoid. I finished mowing that field...
I had a problem with grinding when engauging the pto. I got the clutch adjustment procedure from other post here. I tightened the pto adjstment bolts #6 about 1/4turn that fixed the problem . I was mowing some tall grass on sat. I noticed the pto slipping so I loosened # 6 1/8 turn. The pto...
I have a jm 224 just recently I noticed
that I was having trouble getting the
Pto to engage. Yesterday it would not
Engage at all. I had to kill the motor to get
It to engage. Or grind the gears. I know
Nothing about a two stage clutch except
It works with the Pto and the transmission
The...
I installed a new mecanical oil pressure gage last week. I was using a 5 ft finish mower this morning. At start up oil pressure was 60. After mowing for about thirty min. the preasure was around 35 psi at 2000 rpm. Is this normal? My old factory gage never moved very much. Thanks for the input...
I was replacing my oil gauge when I noticed that wire #39 was loose . It is green and it is close to the fuse box. I traced the other end to the preheaters. I looked at John's website for a wireing diagram but the wires are not numbered the same . Is there a diagram that list the wire nmbers? I...
Has anyone bought an after market oil sending unit at there local auto parts store ? correct me if I am wrong. I assume that as long as you get close to the right ohms reading it will work. Thanks Robby
I have a JM 224 The fuel sending unit has acted up ever since I bought the tractor. I pulled the sender out today there is a broken wire inside it . I have read many post about faulty senders. Is there a way to repair it or should I purchase a new one ? Has anyone bought an after market gas cap...
This was done on my jinma 224 ( 30 min )
This will help you change the main seals in the piston under your seat.
1. Lift front of tractor eight or so inches off the ground.
2. drain hydraulic fluid the drian is the botom left bolt on the rear cover part # 160.55.140-1 (46)
Remove rear cover...
I have changed the o rings on the main hydraulic piston on my tractor before. The problem was I lifted an implement to high. This time I did not lift anything to high or lift too heavy of a load.
Has anyone replaced the seals ( o rings ) without removing the "power lift case box" ?
Can you...
I have a ford (I think it is a woods) tiller 42 inch 3 point . I need tines . I can get them at ford but they are very expensive. Do you guy's have a better idea. Thanks Robby
I have posted a few times in the past few days about a 3 pt hydraulic problem. In summery I had a 3 pt that would not work properly. The o ring and Teflon washer were blown out . I changed the o ring ( part #15 63x5.7 and the Teflon washers . part # 19 a63x2). I took the piston and cylinder to...
I posted a few days ago (hydrolic problem). The problem ended up being item 15 and 19 in this picture . What would cause this problem . The o ring was in two pieces and one of the plastic washers was in several pieces. Thanks Robby http://www.johnstractor.homestead.com/files/HydPowerLift.jpg
The 3 point lift is leaking down . When you lift all the way up it will hold(tractor running). When you lower the 3 pt. it will leak down and put a strain on the motor(tractor running. When you turn the tractor off it will leak down . The hyd. fluid level is good. Any advice would be greatly...
I had a crash on my computer and as always lost some info. There is a web site that is mentioned on this forum several times. I think it is Johns. He has several service advisories ,several good pictures and so on for Jinma tractors. Can some one give me the addresse. Thank you Robby
I have a 224 jinma. The 30 amp fuse for the ignition switch blows every time I try to start the tractor . I can start it by jumping across the starter but I have no gauges or lights. This fuse is the top one in the fuse block. I have the blade type fuses. There must be a direct short to that...
I have a jinma 224. I have changed the flasher (part # sg-3c) for the turn signals 5 or 6 times in three years. I have replaced it with original parts all but one time. I tried one from the auto store the other day and as soon as I turned on the signal it blew a fuse . Do you have a cross...
I have a 2004 Jinma with a 1999 y380 in it 150 hours. I checked the oil and the level was way to high. I suspect that it is fuel. I see no bubbles leading me to believe that it is not water. I would like any suggestions . Thank you Robby
Will a Koyker 210 match up with my Jinma 224? The loader is not new it came off of a Ford. It has all the brackets and hoses. It is a quick disconect. Thanks Robby
After I post the message I check I want to preview post and/or attach a file,push the browse button, find the picture on my hard drive, open it, hit continue finally push post this message. I hope you can help, Robby
I have found out that both of my drills are model (b). The pictures are the parts that I need . I live near Fort Worth Texas. If you know where I might get used parts I would appreciate it. Thanks , Robby
I have an old 12 foot John Deer drill that needs some parts . I use it on a deer lease. The part that holds the disk blade is the problem. I think it is called a (bottom). Are there any available in north Texas. I am not sure how to tell what model the drill is. Any help would be appreciated...
I have a hay ride tonight and the flasher has give out on me . Has anyone used an after market flasher ? If so do you know the cross over Number. It would be better to have the flashers just for safety purposes. Thanks Robby
I have seen on this form somewhere that there are three drains when changing transmission fluid. One in the back by the draw bar , one under the creeper box. I can not find a third one. I have opened the two and got approximately 3 gallons of fairly clean fluid. However it does not resemble...
Does anyone have a procedure on priming and bleeding the fuel system on Jinma tractors. I would like to learn now rather than later while out in the field somewhere. I hope not to ever run out of fuel. I will be changing the filter. Thank you Robby
jinma Oil capacity y380
Can you tell me how much oil the y 380 holds including the filter. I really think that Jinma needs to spend a little $ on there manuals. There is not enough information. Thanks Robby
Has anyone turned there 224 motor up any? I understand that there is absolutely no difference in the jm224 and the jm284 motor. I am no mechanic but how hard can it be to turn up . Robby
I have a jm 224 3 cyl 2004 mdl. I need to know what oil filter to use. The owners parts list says use 480g-09300. Everything I can findon the web refers to jx0706p,jx0710c or j0810h. I am a little confused. Thanks Robby
I have a ford 105 42" rota tiller that I need to get some parts for. I can get them at the local ford dealer but they want more for the parts than the tiller is worth. I have heard that woods made tillers for ford. Do you know if there are parts available without the ford name? Thanks Robby
I have read many post on this matter. Correct me if I am wrong.
1. Drain out the 30 wt oil that came in the tractor.
2. Fill with deisel.
3. Start tractor , turn stering wheel back and forth , raise and lower the three point . (no fel )
4. Drain deisel.
5. Clean screen .
6. Refil...
I picked up my tractor last Wed. I did not try the pto until today. Well It does not do anything in high (1000) or (540) speeds. When I move the engage lever it practicaly goes all the way to the floor. There is no noies or anything. I looked where the lever has an angle that in turn pushes a...
I have read all the post and answers about new jinma tractors that will not start in cold weather. My tractor will not start in 40 degree weather with out some trouble. I have installed a ford switch, I pulled all the glow plugs out they all read 2.4 ohms on the bench. I checked for voltage...