Search results

Does anyone have a parts list for this? I got the baler with the net wrap installed. Luckily it came with the supplement manual for it but no parts break down. Here is the supplement if interested. https://www.mediafire.com/file/l8qgawv938y8pua/wrap_supplement_a.zip/file...

I need to replace the bearings on the shuttle on top of the baler, any tips to help do this?

I need to replace a clutch in a 250as and would like to know what the finger height should be when installed. I could not find it looking at the manual, only peddle adjustments. Thanks

Thanks for the reply. I took a look at this but didn't find a problem but it makes sense that it is there. The other day I used the tractor for a couple of hours without fault. Then the next day it happened a couple of times, once after hitting some ruts and bouncing around. Most of the time...

not mentioned in owners or repair manuals

Mowing field about a hour when tractor stops moving, R/F flashing on dash and buzzer sounding. PTO still driving mower normal, engine temp normal. Shut down and check hydraulic, normal. Tractor starts right up normal, Forward engages normal. Mow for a while and it does it again. Turn off, on and...

Both the parts and service manual show this as a floating detent. Cylinder seems to float in this position. I went and attached a open hose on each port and started the tractor with it in float with no oil coming out. I may be chasing my tail with this. Need to set up a gauge to watch the...

I am using the float position on my remote when using a drum mower. The hydraulics heat up to the point that engaging gears is delayed. I have 700 hours on the tractor. My understanding of the valve is that the fluid should flow through the body the same as when in the neutral position so the...

What or how does the Start Spring function?

Air filter is removed at this time and no blockage.

Helping out a friend with his RTV. He shut it off one day and it hasn't started since. He had someone else look at before me. From what he said the fellow removed the injectors and looked them over, replaced the fuel filter, had him put an electric fuel pump bypassing the lift pump, and had him...

I have a IH cylinder that I would like to repack but can't find it listed. The number on it is 381801R1. Thanks for the help

I have a 1100 and can't seem to keep water out of the hydraulics. Is there a case vent for the transmission or rear axle housing? I can't seem to find one. Thanks for any help.

I have a 479 that has the yoke ear broken off. Priced one at the dealer and figured for their cost I would try my hand at repairing it. Found a yoke to fit the cross, SKF UJ187305. I cut a portion off the bottom of the new yoke to get it closer to the height needed. I needed to retain the...

I have the u-joint but the problem is that the yoke broke off one side, I need to replace the yoke. TSC has pto yokes but not for this size, nor is it listed in the Weasler catalog. Bearing Diameter A. 1.00" Overall Length B. 3-1/8" Lock Up Dimension C. 2-11/32" Inside...

I have a New Holland 479 that had the yoke broke on the slip clutch [86500915]. It uses the 47621 u-jount, crosses to Weasler 200-1875, 1-1875 Neapco. I would like to cut the broken yoke off and weld in a new one but have problems finding one to weld on. Does anyone know of a yoke that I can use?

The operator manual refers to "external auxiliary hydraulic control valve" supplement or manual that was packages with the manual. Does anyone have a source for this? I seem to have all but this one. Thanks

I have a L185 that had a belly mower driven by a front PTO. It used a electric clutch but I can not find any information for it. What is the model number of this? Thanks

I have a Case 450B that would not start. It had run well before but had been sitting for some time since running last. It would turn over but would not start, no smoke from stack. I had fuel at the filters and the pump. I cracked the injector lines at the injectors but had no fuel when cranking...

I had a gate cylinder leaking badly on my Hesston 5530. I purchased a pair of rebuild packing kits a while back but didn't understand at the time why it included a square rod in the kit. No instructions were included and no mention in the owners manual. Looking at the cylinder I wasn't sure as...

I installed a bowl type filter on the RTV since I didn't care for the in-line filter. I made the bracket from thin angle rounding off the corners. I used a 6A320-58862 filter. I mounted it to the rear tapped hole on the frame. The filter has a third hose fitting in the center which I ran up to...

Does anyone have a source for the o-ring and backer for the quick connect? Mine are leaking and the dealer has no listing except the whole unit.

My windshield was offset to the right and would not latch closed. I loosened the hinges and adjusted the hinges in order to latch it but the hinges didn't look right to me. Are they supposed to be bent they way they are or did they get messed up and need bending back straight?

Found the number, K7711-63170 SUPPORT, AUDIO (mounting kit). I'll order one for my install. I figure that the dash could use any support it can get. Mine is crack just below the shifter I guess from other jamming the shifter instead of waiting.

What would you feel this one would be worth? Has 1700 hrs, engine runs, body rusted, tailgate missing, A/C shot.

Well I took it out today Here are some pics.

I got this from a gov auction, a two for one deal from a collage in NJ. Both are cancered but this one is the worst. I've really gotten to hate powder coating, moister gets behind it and the rust starts and spreads. Some places you can pull off large pieces of paint. Seems most stuff you buy now...

Cleaning up my auction find and I found something that just is not good.

I would like to add a radio to the RTV I had just bought. It doesn't have one installed and the blank plate is missing, not sure if it had one installed in the past. Reading some of the posts it is mentioned that Kubota had included a support bracket loose with these machines but mine doesn't...

I think I know why the guard and frame was pulled out. After beating the frame and guard back in I put it back together and found that there was a gap underneath. I guess that a part must not have been right and when it was assembled it pulled the front down and deformed everything. I made up a...

Just bought a 2009 RTV1100 from an auction with a curtis plow. Would anyone have a copy of any documentation [owners manual] for the plow? The mounting plate wouldn't allow the plow to mount up, looks like it could have been jacked up using the center of the plate. I removed it and pushed it...

Anyone have experience with a 3088 hydraulics. My neighbor has one and the other day lost the hydraulics and down the hill through the woods it went till it hit a tree to stop. It seems to lose it when idled down or when hot. The pump has been replaced by the dealer and had thought that the...

Some Massey manuals I have and scanned. Hope that it helps someone. http://www.mediafire.com/download/talgc5opk3e777t MF 65 Manual Set.rar - 458.9 Mb http://www.mediafire.com/download/nmx4rej1n44cad6 mf 130-180.rar - 7.5 Mb http://www.mediafire.com/?53rbellblxszw MF 36 SWATHER 42 HAY...

http://www.mediafire.com/download/6cgbngtv3xho81r JD 480 mower OM.rar - 30.4 Mb

A few more manuals. A couple I found on the web, thanks to those uploaders. http://www.mediafire.com/download/b8g48db8snrl554 New Holland Haybine 469 OM http://www.mediafire.com/download/grp9ovmaaa9hjjg New Holland Hayliner 268 OM http://www.mediafire.com/download/98t0agpxk0f4gop New Holland...

Here are a couple more manuals if someone can use them. http://www.mediafire.com/download/67qtotc2v3sm39v Hesston 5530 operater manual http://www.mediafire.com/download/jbo9ty7yar5w7zt Hesston 5500 operater manual

I have some baler manuals here that I scaned if anyone can use them. jpg format in a zip file with no password. http://www.mediafire.com/download/m1bpdb6q3b6gyy9 Krone Round Baler KR130 & KR160 Operators Manual http://www.mediafire.com/download/2kvrmva3wmdoy4o IH 430 & 440 Balers OM...

I just purchased a MF 36 Swather at auction this weekend. I am looking for a scanned or original manual to buy. I haven't had any luck at finding one on the web.

Hello, I have a Case 450b and would like to get a copy of a wiring diagram if anyone would have it. I have a shop manual but it is for a straight 450 with a generator. Thanks for any help

I purchased a 9HD at auction with a skid steer mounting plate. I need help with the skid steer end. I have a bobcat 873 that I want to attach it to. Does anyone have a photo of the frame mount on the bobcat?

I just purchased a sickle mower at auction and need help with it. There are no tags on it and it has been repaired in the past. Best I can make out is that it might be a Enorossi with a 7 foot bar. I would like to get a parts and owners manual if any are available. The main problem is the...

Hi, I am looking for the torque pattern for the G176 engine. The IT manual states to go in a circle pattern but I would think that it should be like the Continental TM engine where you tighten above the cylinders first and then along the left side at the push rods last. I have a manual from...

Hello, I have a 65 torn down in the shop that I am tinkering on. The question of the day is on the hydraulics. It has a 2 spool valve on it and I was hoping someone had a copy of a manual for it, parts and or operators. It is not a Massey as in the manual but a aftermarket, maybe a Vapormatic...

Hi, I ordered a block heater (70000 73274) for my B8200 and not sure where it should go. The instruction sheet is for a excavator but figured it would work in general anyway, no such luck. It shows a plug to be removed with a hex head but this block has only soft plugs. I called the dealer to...