Search results

I have an 18 yr old KK still going strong, just keep it greased is all.

OK I thought there were more than the 2 bolts so I figure pattern don't matter. So I was looking for the torque for the 2 bolts. I bought it in Spartanbugh SC. There is really only one JD dealer here in western NC and they get away with charging ya double what list price is for any part. I...

1195 hours It was to the point that after about 5 minutes the handle is hard to move and has toi be moves back to center. Bought the new bucket control about 6 months ago and now have to install it. Can anyone give me the bolt tightening pattern and the torque I would be thankful.

Bought my new bucket control about 6 months ago and now have to install it. Can anyone give me the bolt tightening pattern and the torque I would be thankful.

Bought my new bucket control about 6 months ago and now have to install it. Can anyone give me the bolt tightening pattern and the torque I would be thankful.

Ok I purchased a new bucket control. Hopefully putting it in one day this week. Does anyone know the torque for the bolts would be? Or where I could find info, where I bought it was useless.

No rebuilt kit but ya can buy all the parts individually, except the spools I think they are called. I did order the control valve though.

No not yet. Kind of skidish spending $600.00 for the control valve. But there isn't much else it could be.

I don't know what temp the control body is to be at but after mowing for a few hrs the bucket control is very hard, the valve body temp is about 145* and it's 85* outside.

Ya wouldn't happen to have a part number would ya?

I will be cutting grass today so I will check to see if things get hot or not. As I said the longer I use it the stiffer things gets which is why I was thinking something was passing where it shouldn't be the longer I use it. TY!

No 100% stock. The only thing other then PM I ever did was 2 batteries and a few cooling fans over 16 yrs.

about 1100 hrs. Located a new valve $600.00 but no rebuilding kit, ya can buy all the parts individually though.

Put it all back together, linkage. After 15 min or so of running the tractor there is resistance lowering the bucket and it don't stop unless I put the lever in the middle and also curling the bucket but that will stop when I let go of the lever. I am fighting pressure, the longer it runs the...

I disconnected all the linkage and the one piston does not come out all the way. I can pull it out easy enough with my fingers. Going to grease everything today and put all back together today and we'll see how it works out.

No cables all linkage. Feels as though u are fighting against hydrolics.

I have a 2305 with a FEL, a few yrs back I had issues with the control. Took apart cleaned and oiled and it worked although not perfect. Now even though all works the stick doesn't return to center, there is a lot of pressure in all directions and the longer I use it or the hotter it gets the...

My 2305 seat is about done. I am looking for an after market seat with more support, my cub cadet zero turn has a seat that supports your entire back over a bump, don't want to spend a thousand dollars either though. Looks as though I may have to get the bracket also but if that is to costly I...

We're cleaning up where I work and I have the opportunity to buy a 2320 with 1100 hrs, backhoe and bucket that looks brand new. It was used primarily to move dirt and dig up landscaping, some snow removal. Problem is it don't move. It just stopped about three yrs ago and has been parked ever...

Since my last post I have acquired an older Blue. No UT numbers just an SuperXL AO then a 7 digit serial number. Can't find any dating info yet. Spend 30 minutes cleaning it up and she runs awesome. Does need some small things. Spike, air filter knob, new muffler bolt. These are just a little...

Good day all. If ya remember last yr I loaned out my tractor and the trans fluid came back Fried (Black) and the forward valve was bad. I replaced the fluid, filter, and cleaned the screen three times since and all seems OK. Was ran in 90* heat for days with broken trans fan. I am coming up on...

Just about every time I take out my tractor I use my FEL. This yr it seams as though the Up/Down control gets stuck, Scoop/Dump always work fine. If I raise the bucket then go to lower it it will get stuck, it's like it's hitting something solid, not mushy. If I just wait a few minutes without...

OK I bought my saw used for $75.00 back in 83-84. So this weekend I was cutting some firewood and my saw would just die like running out of gas. Took it home changed the G-filter and line that was hard as a rock and only a few yrs old. Until then I had the same line and filter in it for 25+ yrs...

OK All back together and back to normal. The on-line JD Parts store was a scam bait and switch. Two days after putting in the order and paying I received an E-Mail saying the part was no longer available and replaced with the new part for 3x's as much of course. I got a refund and went to the JD...

Try to make this short but a long story. LOANED my tractor out and didn't get it back for over a month. It was left outside longer than it's ever been in the 10.5 yrs I've owned it. Anyhow hydro fan broke and they used in for 30-40 hours with it broke I figure. Fluid is fried to dark brown or...

I have a small Craftsman Mid-Engine Rider Model 536.270302 made in 2005. Broke it out today and started up no problem. let it sit a while and off I went. After about 5 minutes it just stopped moving, no forward or reverse. Figured it was the belt but all looked good. From what I see the Pulley...

I have searched but came up empty. I need u joints for my drive-shaft and understand Kabota has them for their machines and are the same as JD. Unfortunately JD only sells the entire shaft at over $500.00 which I just can not afford at this time. Any help with pt numbers would be helpful. Thanks.