Search results

Built me a storage bracket for my AGRISTORE USA Cat 2 Clevis Hydraulic Top Link. It came with the tube mounted on top already. Actually it has two with one mounted almost mid way. I just bent me some 5/16 rod into a shape (somewhat) similar to the factory standard John Deere top link. The strap...

Finished except for a little paint to keep the rebar from rusting. The fork slot forms are giving me some trouble to get out, but I allowed for that and made sure the forks would fit the slot even if the forms were in there and had to come out slowly. I am very pleased with it and look forward...

Closer to finished. Letting it cure just a little longer before I hack out the fork slot forms. I need to paint the rebar loops. Makes a world of difference with the back end planted on the ground.

This winter has been brutal for North Alabama standards... We usually get a little snow in March too!

Concrete poured and curing. 21 - 80lb bags. With Rebar and water, should weigh in some where around 1750lbs without the landscape box attached. With box I should be about 2200lbs.

I have noticed threads that people post to soliciting surveys for the topic of the forum and a link to LINK REMOVED Should this be looked into by TBN Staffers? Spam? Malicious?

Have it mocked up with all but 1 piece of rebar. As usual, come up short of something on a project. I will strap the front 2X4 to one in the back but it is pretty tight. Don't think I will blow anything out. Should I paint the inside to prevent the OSB from soaking up the water from the...

Getting Closer and becoming a little more obvious now. 2000lbs when complete (not including the landscape box). I need to make sure I cast this baby close to the front door of the garage to get it out when she is done. It will have dual capability. I can pick it up using the scarifier slots and...

Since this is a "Ballast" thread, I will give you a tease picture and see if you can guess what it will become.

Here are a few of the Frontier AY12G. It has a double bottom with a arch to strengthen it and to force breakup of pack clay or dirt as it crossed it so it doesn't stick like a smooth flat bottom creating resistance. Also has a 1" blade front and rear of the clam.

Pulling up trees and shrubs can be difficult with a Grapple Fork and impossible with a bucket but a cake walk for the 4-in-1. Pros and Cons with each.

I have a Frontier 4-1 82" bucket on the front of a JD 5075M. It too weighs over a thousand pounds, but it is mounted on an H260 MSL loader and simply hang ballast (6' rotary cutter or box blade with a mounted water tank on top) off the back. I don't have any problem pushing it around as a dozer...

Hey John Deere guys. Question for the Northerners. Relevant Info: 2013 John Deere 5075M, Deluxe Operator OS and Gauges, Standard PowrReverser 16x16 MFWD, standard glow plug starting aid, no additional cold weather equipment. Stored in unheated barn. 140 Hours. All fluids checked and proper...

On the trailer.

Easing through the barn with a 8 and a half foot wide, 28 foot long flatbed trailer. The tractor just squeezes through also.

Why I have a tractor. The pictures of the rider is my daughter in competition. The rest are our farm.

Can you guys come up with a 3pt Hitch to John Deere Global Carrier like Stoll's in Germany?

You are da man! The dealer left off a bolt! (said there was nothing they could do about it). I am pleased that it wasn't John Deere, as this is a dealer assembled item and deere had indeed not poorly designed it. Look where your washer and spring are stopped by a through bolt on the shaft and...

Look here OMSJ14575 Service Interval Chart, 7th item down. Do you have a plate on top of the axle at the wheel with 4 bolts holding it down and one just like it on the bottom?

Hi Folks, Me again. I have a new H260 with a Global Carrier and I have a peeve about the latch pin. When I pulled the pin, it takes some force. When it releases, it pulls completely out of the far tube housing. I complained to the dealer (New tractor and loader) they said there was nothing they...

Hi folks, Newbie here to TractorByNet, but I have to give a shout out to AKFish and LARRYINPARKS as I followed a lot of their posts prior to purchase of my new tractor. I have a 2013 5075M and need some clarification about maintenance. The maintenance schedule references at 50 hrs to Lubricate...

Anybody know who offers a 3 Point Hitch to Euro/Global Carrier Adapter? I have seen one manufactured by STOLL in Germany, but nothing like it yet in the US that I have found via the web. Stoll part number is 3386990 and can be seen at...

TriGreen Equipment finally delivered my elusive John Deere AY12G! The first one was stolen from the carrier in Atlanta or at least that is the last place it could be tracked anyway. I was concerned with ballast, but with attachments on the back, I think we will be just fine. Th H260 MSL Loader...