Search results

Anyone replaced the water pump? Do I have to pull the whole front end off first? Not much on Youtube. Any pointers? It is dripping after you shut it down. Don't see it leaking while its running.

May seem silly, but I am looking for a glove that won't wear holes after three or four uses. I cut, split and handle firewood at least 3 times per week and I like the gloves that I am using now, but they just don't seem to hold up very long. I am using hydra hyde with the velcro around the...

I am having a tough time finding a good webpage that shows exactly what I need to replace the bar on my Makita 7300PRZ with a 20" bar. Here is the current chains I am running. Oregon 73LGX072G Power Cut 20" Pitch: 3/8", gauge: .058", drive link count: 72I \\ I ordered what I thought and it...

Ok so we have 4 sets. Two sets for the buck and the other two sets one works the grapple and the other is open for implements. One set on the outside left side we have had to replace the SCV's 3 times already. They leak and couple times just blow out fluid everywhere. The set that is on the...

Ok so we have 4 sets. Two sets for the buck and the other two sets one works the grapple and the other is open for implements. One set on the outside left side we have had to replace 3 times already. They leak and couple times just blow out fluid everywhere. The set that is on the grapple...

We have a 6400 and one day I was moving a bale of hay and I lost hydraulics light came on and I started to get smoke from under the cab. Upon inspection i noticed that the smoke was coming from what you see in the picture. So I know nothing about this and what it does. What am I up against...

So I know Makita bought out Dolmar but did they make changes to the saw or are they the same machines with a different name. Has anyone purchased one lately? I currently have a Dolmar PS510. Thanks

If it ain't one thing it is another!!!! So got the tractor all cleaned up and was getting ready to put the shredder back on it, but wanted to go knock down a very small dirt pile near one of my boy blinds. Did that job and on the way back to the house I saw a small tree down in the road. i...

Ok have a 15 ft bat wing been using it fine for awhile and everything worked fine. Hooked her up the other day after a few months of not shredding and the PTO engages and then the light blinks and PTO shuts down. I am up to the required RPM's and I am no leaving my seat. It works for about...

Ok it runs fine but if you shut her down and let her sit over night it won't start right away the next day. We turn the key on and wait and it will fire off and die. Work the throttle and turn key on wait and then try again and it just turns over and won't start. Turn it off back on again...

Hey guys! Family bought a used 6400 couple of months ago has about 5600 hours on it has the 620 loader I believe. Father in law was doing some road work and was on it for about 2 hours and got a stop engine light which showed to be the hydraulic fluid over heating. We changed all the...

The right one is working fine but the left side leaks slightly and it seems to not respond well especially when cold. The tank has plenty of fluid. Any ideas. Can you rebuild those things?

I am looking at a TD95D with a bucket and 4wd no cab and he is asking $24,900. It has 2156 hours and it is a 2006, is that in the ball park? thanks, Mike

I have a ford 1520 with narrow utility type tires, I need to put wider turf tires and rims on it. Any ideas where to go to get these? thanks, Mike

I have a cub cadet zero turn that is made by MTD and it has a Briggs V twin intek 22hp engine that is blown. Anyone have experience replacing these and where I could get the best deal on a new engine?

I have my grandfathers old Cadet 75 it is a rear engine that has briggs engine and I am trying to swap it out with another but can not get the drive pulley off the crank shaft. Any ideas where I could look for a replacement?

I have had this MS 250 for just over a year, I used it last month with no issues took it out this weekend and I could barely pull the starter. I might get one rotation and moved but very difficult. The first thing I did was take the spark plug off and still the same issue. I then took the...