Search results

You only read part of it, but that's ok. I will take my chances. I think if we can put a man on the moon I can seal that. Of your 2,000 plus posts, I bet a high percentage finds fault. No need to respond back, please just keep scrolling to another

read what I wrote

It has a light coat of clear silicone all around it, and where the key goes in. Not inside, just around key to switch

Well, we all are i guess. I am from Pittsburg NH and was in Montana recently seeing my daughter. While at the grocery store a total stranger, older gentleman, came up to me and said, totally out of the blue, "you know how I know I am getting old"? How is that I asked this man. He said, "after I...

Why does JD put the key where they do? Keys are dime a dozen, but when you can not get the broken key out it becomes an issue. When you forget it just once, snap!!! No more for me. !!!!! I ended up not being able to get one out so I got an aftermarket switch. Didn't even check OEM price! I...

I have that exact welder, love it!!

Thank you my friend. You drove from MN to Idaho to pick up a dog? Rescue? I may be going to Texas to pick up one if she cannot find a fantastic home. It has got to be the perfect home or I am heading to Texas. Guess we do have a lot in common. haha. Now, if only I could fix my damn knee.

That could get nasty. My 2 cents, did the neighbor call you or someone else? Personally I would wait a bit and see what the neighbor says. That is huge I would think. If he comes in good faith hopefully something can be worked out. If you were called by someone else and you have heard nothing...

Glad it was good in the end. To this very second, I have no idea how I leaned into my table saw. Was ripping 2" pine for stair railing and clink! The bone in my thumb. All the way across the top of the hand. Got to ER, I had lost a lot of the red stuff. Woman wanted information. I need to be in...

Well, I guess some of you hit it perfectly! He has 3 ranges with 3 gears each. He was in the second range. I did not want to belittle him at all. I suggested that some folks on TBN suggested possibly using the lowest range and a lower gear on the more difficult stuff. The clutch play to the...

I know he has a larger area to work wih, I think you all may be on to something here. What's common sense to some may not be to others. I am hopefully going to see him at his house this weekend, I will get more information then. This site, TBN, has always always always given me such valuable...

he came back with a 3 speed gear box. Would that possibly have two ranges? If he is say in range 2 it very well could be too high a gear for what he's doing?? I would think too much of smelling this condition will have adverse effect on the clutch.

I am posting for a friend, he has a 40 hp Kioti. While moving snowbanks that have set up, he is smelling what smells like "burning rubber". If in softer material he doesn't smell at all. It appears to be while the unit is working harder to move the snow. I asked him if the temp guage rose when...

Well, sorry for the delay but here goes. Putting the caps in, at least for me was no easy task. As mentioned earlier they have to go in straight. I didn't have a large enough socket to encompass the entire cap so I used a 3/4" socket which set on the flat spot of the cap. The problem was, on my...

WOW, Thank you "been there" you hit it right on the head. YES there is a drain plug on each side. It never clicked where the plug is in relation to the cap. I called united ag in vermont, unfortunately they were not much help, I called another dealer closer to me. The mechanic said the SAME...

My mind is workng overtime here. Being the seals on both sides are leaking, if they were not leaking there would not be any fluid from the cap (if they were in place) looking upward. That void is say 2"wide and an inch or so up. I am having some trouble by the dealer saying by putting in the new...

Here is the lastest at this point. A young friend of mine lives in Vermont, I now live in Pittsburg NH. He was near a JD dealership yesterday. He showed the pictures I posted to the service manager there. After viewing he had a tech come and look. The feeling at this point is, if I replace the...

I have 2500 hours on my 4320, never had a problem until recently. like you, why would we adress it? Have to address it now though. This is a NON educcated guess on the cost. It must be a grand per side? I recently checked on a loader greasable pin, that was $91.00. That is just stupid price in...

I am not overly mechanically inclined, this isn't looking good to me. Attached is each front wheel looking up. As others have mentioned a cover is supposed to be there. Shocked to see NO COVER!! Both leaked within a couple of days. One whould have thought after seeing what I am seeing, where in...

Your explanation makes perfect sense. In your case the press in plug pushed out. My fluid isn't coming from the drain plug, rather the bottom of the housing on each side. If you look real close you can see a slight stream of the fluid. I have not crawled underneath to look at the housing. I am...

What are the odds? The left front tire where you drain the front axel fluid, I noticed a fluid leak. Brownish colored on the snow. Tractor hadn't moved in a few days. The day before there was nothing on the ground. Well ok, must be a seal under the housing. Next day there was a lot bigger spot...

Not sure the rear rims you have, if they are bolt on inners, you have some width options at your disposal. I am currently experimenting with the very same issue but on a JD 4320. If your rims are welded inners there is not an adjustment. The manual for mine indicates 8 different options. The...

But, you are really getting old when you go take a whizz, and it's not down.

When I first read this question my reply was EXACTLY THAT! My wording was a tad different however. I used the wording Touch and Hole! Well said my friend, well said!!

I had a typo in the first post, I said 6-16. They are 8-16 R1 (original) I am going to call a dealer tomorrow to see the correct size in front. I see you have a 4300, tire size for that unit is 15 front and 24 back. Did you watch the Pack destroy the cowgirls? Loved it!! TY for your reply Dave

Hi, I am changing rear tires soon, and was wondering about the fronts. You mentioned you changed fronts due to dry rot. You also mentioned turf tire. I am confused on if you changed the front tire size, I think you did, you said they were too tall. I am going from 13.6 x28 to 16.9 x 24 {rears}...

Ahhhh, thank you for your reply! I did it as the previous post said, no issues.. Maybe you can answer this one too. The original tires, rear, are 13.6 x 28 R1. They are severely checked. Where I am now an R4 tire will be better suited. I know I have to change rims too. I would like more...

I too was in this exact same situation a few years ago. My wife had bought me for xmas a Hobart 190. I believe it was only a 110 v weleder. I ended up exchanging it for the more versitile 210 unit. Being the homeowner and diy'r I just thought it would be a better unit for me. i had to use a...

Sorry for the delay, TBN wouldn't let me in. Long story, I'm finally in now. I should have been more specific, it is leaking that is why I had to change it. CADplans mentioned about welding a piece around the hole in the timing cover. I was considering trying JB WELD. However, being there is a...

I went to change out the water pump on my 2006, 4320 JD today. I spoke with a mechanic at a dealership here in Vermont, Yandows in Ferrisburg. I have the utmost respect, been in business a long time. He cautioned me that there is a potential of the timing cover being damaged from the bearings...

Hello to Everyone and thank you for allowing me to join. I'm sure I will gain a wealth of knowlege in time to come. My wife and I live in Central Vermont in a logcabin that my Dad and I built 1n 1978, we moved in in Oct of 1979. We have lived off grid since. Although power is now within our...

I have a 2006 4320 JD. The front tires the first year showed severe age cracks. I went back to the dealer back then and was given no help at all. I have replaed both front tires and they are ready to blow again. I doubt I am not alone with this problem. Anyone have any suggestions for a...