Search results

I thought this may benefit someone that has a 3510/4110. The rubber boot on one of the tie-rods seemed to have come out from under the clip that holds it in place while I was pumping grease into it. After removing the tie-rod, clip and boot I noticed the boot was stretched out, and I was not...

I am flushing out the radiator on my Mahindra 3510 and installing new coolant. I read on the Fleet Charge site that regular tap water can be used. Has anyone done this with good or adverse results? Here is the info I'm asking about. FLEET CHARGEｮ fully formulated coolant eliminates these...

After being patient for over a year, I finally come across a good deal on a box blade. A heavy equip. dealer a few miles down the road also had a lot across the street where they sold Mahindra tractors. The dealer dropped the Mantra line in order to concentrate on the heavy equip. and moved all...

I thought some of you may want to capitalize on this deal. It's even a better deal with a 15% off coupon. Promo code "SAVENOW" without quotes. Electric Fuel Pump; 12 Volt; 15 GPM; Manual Nozzle - 3958121 | Tractor Supply Company

Those of you that own a 3510 and possibly a 4110 need to check the fuel line that runs from the fuel pump to the injector pump on the right side of the engine. It is a 5/16" ID rubber, single layer fuel line about 6"-8" long that attaches to the injector pump next to the injector pump bleed...

I am in the market for a diesel generator. I'm looking for one that will supply about 10,000 watts continuous and as portable and compact as possible. I have found several on-line, but was wondering if anyone has any experience with any particular brand (good or bad). I'm not brand loyal, but...

Here is some pictures of a set of forks I built for my FEL. The frame is built out of 1-1/2" x 1-1/2" x 1/4" square tube 3-1/2" x 3/8" flat bar and 1" rod. The quick attach plates were ordered on line already made and welded onto the frame. The forks came off of a Bob Cat SS. These were too...

Does anyone know how the buying or renting, exchange program works at TSC? Joe

Here is a fuel tank stand I built for a 75 gallon tank from a Mack truck. The skids are built out of 6" channel iron with 1-1/2" ID pipe used for the spreaders. 3" flat bar was welded to the open side so it could be securely transported by a set of forks. The cradles were made from a section of...

I was at TSC today looking at the Premium Universal Tractor Hydraulic Fluid. I stopped the store manager as he walked by and talked to him about the fluid. He told me the Travellers brand was made by Shell and relabeled for TSC. After I returned home I searched extensively on the web and could...

About a year ago, a friend of mine loaned me his landscape rake. I quickly realized how valuable that implement was. After Hurricane Gustav he needed his rake back, so I was in dire need of one to help clean up my own hurricane destruction. This was the first full weekend I've had off since the...

I need to change the right front hub assembly on my 3/4t 4x4. I have found two different brands of hubs in this area, National and Timken. Does anyone have any experience with these brands? Thanks. Joe

I used a pressure gage with a QD and briefly dead headed one side of the rear remote hydraulics to get a pressure reading of approx. 2200 psi. When the lever was returned to the neutral position the pressure fell off till it reached zero (about 10 sec). To me, that didn't seem right, so I tried...

I am trying to determine what length of a HTL to get. I am looking at two that may fit the bill. The first one measures in at 19-1/4" - 31-1/4" and the second on at 21-1/4" - 35-1/4". The first one would give me plenty of forward tilt for the scarifiers but would only allow enough rear tilt to...

Hey Guys, I just noticed this today, and haven't talked to my dealer yet (Holiday). I have separation of several lugs on each of the front tires, some worse than others. Is this normal, or should I be concerned about a tire failure in the near future? The tractor has 142 hours and is a year and...

Here is a tooth bar I built this past weekend. 4"x1/2"x72" cutting edge with eight Fabco teeth. Joe

I have been searching the forum for the last three hours and have not found the info I'm looking for. I have all the steal I need to build a toothbar except the teeth. Does anyone know what style tooth is used on the toothbars? Thanks, Joe

Does anyone use this tire balancing system in there vehicles? If so do you recommend it? Tire Balancing Products Joe

Hey Guys, Couldn't come up with any answers from a search so I thought I would ask. I have a Chevy Silverado with 118k miles. I have been using Royal Purple oil since the very first oil change and doing a complete oil and filter change every 9k miles. Here lately the Royal Purple oil has been...

I have the 3510 with the electro-hydraulic clutch. Is there any type of safety device or pressure relief Incorporated into this type of system to minimize the shock load when engaging the PTO. I lower the engine to about 1000-1200 RPM, engage, wait till the implement comes up to speed and then...

Does anyone have the PECS installed on a 3510? After doing a little research I discovered one of the requirements is 4" of straight lift arm. I measured mine and I have 3-3/4" of straight lift arm and was wondering if it would still work. Thanks, Joe

After buying my 3510, and using the FEL for a while, it feels as if the lift capacity is not up to par. The service manual shows the relief pressure should be 160 kilograms per square centimeter which equates to 2275 psi. I tested the hydraulic pressure at the rear remotes with the engine RPM...

Well guys, I finally ordered a Millonzi Grapple on Friday. I received a confirmation by phone that it has shipped today (4/16), and will arrive at the freight company for me to pick up on Thursday (4/19).

Those that have added the third function valve kit, would it be better to purchase the kit such as the WR Long kit (do you use all the pieces), or piece one together from different sources?

Check out this link that is on Mahindras web site. I'm sure you'll find it quite interesting. Emerging Giants

I finally got my tractor!! :D I ordered the tractor on the 18th of Sept. I called my dealer yesterday (Fri. Oct 6) and he tells me it came in Tues. but he was waiting on the mower to come in next week so he could deliver it all at one time. I couldn't wait that long, so I went and picked it up...

I know the tooth bar questions have been addressed in great detail. I have done a search and have not come up with very many prices. Would anyone care to share what a their tooth bar cost them? I am interested in a 72", but all lengths and brands are welcome, as it may help out others interested...

Hello Guys, I've been lurking in the shadows quite some time reading and learning. I would like to introduce myself and thank everyone for a great forum. I am in the market for a compact tractor. Without being brand specific in a general forum, at what point do I need to be concerned about the...