Search results

Toolcats are great for moving snow. I have a 8 ft snow blade for mine now.

Really depends on type and height of grass and how much your cutting off. 4 mph is about my average. I bet into some thick bermuda type in a bottom that will bring me to around 1 mph. Belt slips or hydraulic motor powers out. Most of the big commercial mowers will probably mow faster but thats...

Although this block didn’t, I’ve picked things up that started lifting back wheels off the ground.

Stumbled across this if anyone is looking for 5610. https://www.bigiron.com/Listings/EdwardSpear

I’ll have to check that out!

Has anyone replaced bearings in a Toolcat wheel hub? Parts lookup only shows complete assembly from Bobcat. I getting some play and sounding a little rough when I replaced an axle.

This had the 5610 grunting a little. 72 inch Bobcat Brushcat.

I have the 90” finish mower, it’s covered over 600 acres since getting it!

I’ve seen a couple videos of Toolcat with the Mattracks but, I’ve never seen the loader extension or any info on one. Kind of doubt Mattracks makes one. https://mattracks.co/tracks/65/

Rainy day project. Built sacrificer using teeth from my box grader.

LOL, my funny side note. When my sister lived in Maryland, when visiting, after a few days I’d start feeling “ claustrophobic” because I couldn’t see horizon to horizon for all the trees.

I’ve made an upgrade since pics with it on the Toolcat. Still plan on a Tiltach in future.

I’ll do think Toolcats are overprice compared to other utility tractors even though it is a little apples to oranges. When I moved back out to our farm, I was looking at mowing 10-15 acres just around farmstead. I kind of used the $12-20K cost of a large commercial lawn mower and the fact I...

I’ve been amazed with my Toolcat. When I hit 8 on my trailer, I was squatting real bad on back end. 7 was good with one on front to counter balance. Later I started loading 12 and moved trailer with T650.

My setup.

I used a box grader on a few miles of drive. I can make a crown by adjusting blade level on each side. I’ve run it on the 3 point of my 5610 and also on the front and my T650 using a 3 point adapter. I’ve been able to revitalize the gravel in my yard with it also. This is the one I have...

May have exceeded listed capacity a little.

Trenched about 600 ft with the Toolcat. Set the cruise control in reverse and let it go.

Finish mower and Brushcat 17.5ft, call it 20ft to end of receiver hitch on back, think it was another 3 ft to end of 3 point arms. Back tires are just few inches short of 16 ft. Pics on car trailer is 16ft deck and 18 ft with tail. Pic with both mowers on my gooseneck has 25ft deck and 5 ft...

I was referring to the AC condenser at the bottom side of the cab on drivers side. I have little to no problem with radiator plugging. I did add the pre-cleaner to my air intake and that made a big difference and was well worth it.

I’m thinking about a 6 way dozer for my T650. Looking for input from someone that has experience with them. I’ve seen a lot of info that suggests they aren’t very effective over a bucket and are difficult to use. One salesman told be they make an experienced dozer operator look like a rookie...

I have a Toolcat 5610 with little under 1000hrs. I bought it used with 185 hrs and it has had a intermittent problem with suddenly stopping and throwing a 50-56 code. It usually happens, if it does, in the first 30 minutes of running. Sometimes it will come on parked and idling so it doesn’t...

I never have liked where the AC condenser is located on the Toolcats. I mow a lot with my 5610 and in no time my condenser was plugged to where I had to remove these air cleaner and fan an a few hours of washing and blowing it out. My "fix" was to put a piece of window screen in front of the...