Search results

I did not use enough grease. Now I have to try and dig out what's left of the circlip to pull the remainder of the bearing race. I was able to knock off the inner race from the support plate. Worse yet, I have to rebuild both ends. I really don't want to buy a new roller @ $500. BTW, I...

I have a cracked power steering line. It goes from the right side hydraulic ram to a block on the steering column. How can I tell the difference between the feed side and the return side? It's about a $30 part, so I don't want to buy em both if I can help it. The tractor is a 1986 Ford 3910...

This grinder is old but it runs like a champ. Does anyone know about what year it was built? I did not find anything on a web search. Black and Decker #10 Ball Bearings 110-120 V 13 Amps (That works out as 2 HP) 7" Wheels I feel sure the base is shop built. This whole unit must weigh over 300#...

I never see farm equipment auctions in my area. I finally find one and it's only a few miles away. I'd like a look at the fertilizer spreader, anvils, grinder and the Ford 7' brush cutter. Most of the stuff looks very old. The owner is moving to a rest home. ESTATE AUCTION - Farm equipment...

POF upper with a Spike's lower. Magpul stock, Ergo grip, Troy rear sight and a SS C-Products magazine. Now to find some ammo. My Wallyworld was out.:mad:

What the heck is this weed? I showed this picture to a couple of dozen people and everyone said they have seen it but no one knows the name of it. I have a few hundred to kill this spring before the seedhead opens.

Can anyone tell me what this plant is or direct me to a place that can?

My Wife and I are installing a wood floor in our house. I'm using engineered pre-finished planks 1/2" by 5". I am using a Bostitch MIIIFS stapler as my main tool but it will not fit in the first and last row. I'm shopping for a finish nailer and I have come across 2 types. A straight and...

I saw an auction notice in todays newspaper that listed new tractors. When I looked it up, it was for 25 Framtracs and a Kioti. Here is a link. Tractors

Blade equivalent? I have read in a previous post where the Husqvarna riding mower is the same as a Sears. I have an YTH2348 (48"). What blades can I use as replacements? Or what Sears model mower can I use in searching?

My belts failed. I have 10-15 hours on the flail. Both the power and rotor shaft turn freely by hand. There was no noise or smell of burning rubber. After a few hours of first using the Caroni, I checked the belt tension and they were a bit slack. I tightened them up a wee bit. As there is a...

Hi All. I'm looking to buy a new 3pt sprayer w/boom and handgun. I've been on the web doing searches and I've looked at previous posts on TBN. A few months ago, I was at a TSC store and looked over the sprayers they had in stock. They were all Fimco and each and every one of them had some...

I've had it with the sunburns. Can anyone recommend a reputable dealer to buy a canopy from? I have an 86 Ford 3910 with I think is a factory ROPS. Does anyone make a canopy that can be used as a platform to stand on? Safety Police, please don't beat me up but if that's a stupid idea, tell me...

I have old pasture land that is a bit hard to mow due to dips and holes and a few rises. I recently ran a two bottom plow through about a half acre and after a week, I ran a 20 X 20 Tandem Disc Harrow over it. It's still not the level field I'm looking for. I want land that I can drive a normal...

My rotary mower has made it's last cutting. I had a catastrophic failure. The blade broke at the pivot point. I could buy a new set of blades but the whole mower is worn out. The shaft is bent, the seals have started to leak, the gear box wobbles, the deck is worn through in some spots and the...

I did my first plowing today. There is a learning curve and it got easier as I went along. There was some roots to cut and a few of them tripped the shear mechanism thing. I found it snaps back in place. The grand day out finished when I was going over a already plowed piece and the tractor...

. I bought a 2 bottom plow to renovate some ground that has not been worked in a long time. The plow has a stubby Cat I pin that is machined as part of the plow. It's to short to use an adaptor on as the lift arm is a bit wider then the pin with nowhere to use the lynch pin. I welded 2...

I not sure if this is the correct forum but what the heck. I am interested in setting up a home sandblasting outfit. As of now, I have no equipment that would lend itself to the outfit. In other words, no air compressor and no hoses. So I need an air compressor and a pot(?) is it called? Any...

NEW Lowes Task Force 3W "CREE" 2C 150+ lumens It's the NEW KING of 2 C Cell THROW and Value at $29.95 batteries included. It throws like a Mag but with a bigger hotspot. Be careful not to buy the older model. The easiest distinguishing mark is the Xlamp LED Technology printed on the package and...

A new guy question. What is used to attach a chain to the drawbar? I was thinking to use a bolt type anchor shackle and a top bar pin for easy removal. See All-Lifts, Inc.Shackles and rigging hardware I know from a safety aspect, not to pull from the lift arms but I'm not sure on what's used...

I'm looking to buy one mainly to even out some acreage. I have a 47 hp Ford 3910, 4600 lbs. The soil is a nice dark loamy mix about 6" deep changing to sandy clay for 4" then 2" of small river rock. It is pasture grass with silver sumac and some gum trees trying to get big and lots of some other...

Massy # 43 Bottom plow The local dealer is asking $550 for this plow. It has new (shares?). Is this an OK price? He also has a Ford 101 that is well rusted. Not a speck of blue paint and he wants $450 and it needs new shares. It is in the back of the photo. BTW, what is a moldboard? I'm new to...