Search results

I have a 2004 John Deere CX gator with approximately 900 hours. I bought it new and it has been very dependable. Lately, I have noticed a noise in the rear end, a type of whistling-clicking noise when it is in forward and reverse gears. It doesn't click in neutral; therefore, I think it is...

Do any of you know where I can get rear wheel weights that will fit my YM 1401? I have liquid ballast in the r1s, but need a little more weight.

Will a Massey Ferguson 1705 handle a 3 pt. 9 blade disk with 16 inch disks? Thank you

I am looking for a 4 ft wide cultipacker. I have found models that weigh from 308 pounds up to 800 pounds. I am wondering how much weight the 1401 can lift with the three-point lift. Any help will be appreciated.

The pto on my LX280 will stop intermitently. You can push the knob in and then out and the pto starts again. What do I need to check? Thank you

My friend has a F22 with a fuel leak just below the injector at the primer pump. It is not sucking air but it is a steady leak. I have looked at the Hoye website but couldn't find info or parts. I would appreciate any help.

What is the size of the bolt head that attach blade to spindle? Thank you

My YM 1401 has started overheating and pushing water into the recovery bottle. Yesterday I tilled about 30 minutes and afterward I checked the radiator and block temp. The radiator read 233 F and the block 235 F. I see no oil in radiator nor antifreeze in the oil. I started the tractor this...

I have been using a John Deere pole saw for about 10 years and it needs some repairs. Mitsubishi made the saw for Deere and they do not support parts or repair for the saw any longer. I am thinking about a new saw. I can get a Poulan, Troy-bilt for approx. $180 or I can get a Stihl or Echo for...

The foot operated parking brake on my 550 doesn't work. It is a 2011 model I bought recently and I have the owners manual but there is nothing about the parking brake adjustment. I called the dealer to get information and was told I would have to bring it to them for repair which means...

Browns Community Ruritan will sponsor its annual antique tractor and machinery show this Saturday, July 26. Shaded area for parking equipment. Concessions served in air-conditioned building. No charge for admission or exhibitors. Equipment parts and farm related vendors are welcome. Since the...

I have a 1994 JD model CX gator. The front wheels are wearing on the outside. I can't find any place for alignment adjustment. Any help will be appreciated.

My YM 1401 (2wd) front wheels wobble when the tractor is in high gear. I have done about all the adjustments I can do. What is the recommended fix? Thanks for the help.

I own a John Deere CX Gator bought new in 2004. The front tires are wearing real bad on the outside edges. The gator looks to be toed in too much. The dealer said there is no adjustment. Has any one else had this problem with the CX? Are there any recommended remedies? Thanks for any help.

Have any of you that have pacemakers done any stick welding? I am considering trying to do a little welding wearing a heavy coat and keeping the electrode away from the pacemaker as far as possible. I use a string trimmer and chain saw with no adverse reactions.

Have any of you used the product Seallube? Good or bad

I just have to put my 2 cents into a discussion. I can't understand why grey market Yanmars get so much bashing. Lately I have read on different forums concerning safety issues, parts availability, age and other negative comments. I have owned two Yanmars one a YM 155 domestic and a 1401 grey...

I recently read a book about compact tractors and the impact they have had on different areas of agriculture, industry and suburbia. The book was interesting reading however there were some mistakes. The author stated compact tractors now have more horse power but are lighter in weight thus...

Browns Ruritan is sponsoring an antique tractor and machinery show Saturday, July 27. Location is McLeary Road off Highway 412 East, approximately five miles east of Jackson, near mile marker 87 of I-40. Events include pancake breakfast; lunch - hamburgers, hot dogs, stew and desserts, served in...

Approximately how much hp will it take to pull an 8 foot heavy duty JD off set disk on rocky steep ground? Can a NH 3930 4WD handle it? Thanks

Yesterday I was mowing with my 1401 and the engine died, started again and died. I drained the tank, replaced filter and refueled with fresh fuel. the tractor started and ran fine for over 3 hrs. Today it did the same thing and I thought it may have gotten air. I bled the two screws at the...

Where might I find the wheel spacers for a 5 foot Maschio finishing mower? Thank you

Browns Community Ruritan Club will sponsor an antique tractor and and machinery show Saturday, July 28 on McLeary Rd off Hwy 412E. Pancake breakfast 7:00 to 9:00 a.m. Lunch served beginning at 11:00 a.m. Served in air-conditioned building. Events include tractor parade around grounds, tractor...

I was clipping pasture with my 1997 NH 3930 4 WD pulling a 6 foot rotary cutter. All of the sudden there was a severe grinding sound and vibration. I thought I had hit a hugh rock and destroyed my rotary gear box but that wasn't the case. I uncoupled the cutter and engaged the PTO and it turned...

I have owned a YM 1401 for 11 years with excellent service. I have gotten parts from Hoye without any problem. I am thinking about up grading to a F18 and am concerned about parts availability. I will appreciate any input.

My pump on my sprayer is on-demand and lately the pump keeps running when I release the wand trigger. I have also noticed there is a decrease in pressure when I engage the wand. I have checked all the fittings and they are tight. The pump is a Shurflo gold series less than a year old. Any...

I bought Oregon brand gator blades from my JD dealer. When I installed them there was vibration and a blade came off and I put the one back on and tightened them again (air wrench) and the same thing happened. I discovered the Oregon brand has a 13/16" center hole and the JD brand has a 53/64"...

I am looking for a straight shaft trimmer and have narrowed selection to Stihl or Echo. Any recommendations appreciated.

The Meg-Mo system is a disc with 4 blades attached that replaces the blade on each mower spindle. Have any of you used these and what do you think of them?

What size and grade of bolt is used for attaching the rear wheel to the axle on the 1401? Thank you

I had my alternator rebuilt by a reputable shop and after I ran the tractor for an hour the battery (alternator) light begin to flash. I turned on the lights and the blinking stopped. I seem to remember sometimes generators would overcharge and the lights could be turned on to help. The...

Do any of you know where I can get GL-4 90 wt. gear oil? Thank you.

I need some suggestion on where I need to start. My tractor is dead. Where I turn the key there is nothing not even a click. The battery is hot and I tried a booster but nothing. Seems there is absolutely no fire to the starter. This past week it did this when I first turned the key but turning...

My Gator CX won't start. The battery is hot and when I turn the key There is a loud clicking noise and the engine doesn't turn over. I assume it is either the selenoid or starter. How can I check to be sure which one it is? The engine is a 10 hp Kaw. Thank you for any help.

I am in the need of a push button horn switch for my 1401. Do any of you know where I might find one? Thank You.

What size disk will a NH 3930 handle on relatively steep rocky clay ground? Do you recommend 3 pt. or transport type? Thank you

Do any of you know of a Westendorf loader dealer in Tennessee? Thanks

I have a Yanmar 1401 2WD drive and instead of getting a front end loader I am looking at model WR 20 high lift. The loader hooks on the 3 pt and I need one remote to lift the bucket approx. 50". The cons are no down pressure and it's on the back. The big pro side is it can be removed easily and...

I have the opportunity to purchase a 1985 Power King 1614 with loader and plow. I have only seen pictures however I will be looking at it this weekend. The tractor and loader look good. The tires are in good shape with weigths and fluid. The owner said the Kohler engine is in good condition. The...

I have Firestone 8-16 rear turfs on my YM1401 and they hve been on for 10 years. I need to replace them but have been unable to find the 8-16 turf. One dealer said that Firestone did not produce them any more. Do any of you know where I might find the tires? Thanks

Have any of you had experience with a pull type core aerator. I will be pulling it with a JD 280 and a Yanmar 1401. What brand do you recommend?

Sorry, I goofed and placed this on the Kioti forum! Yesterday, I was cutting thick blackberry brambles and thick weeds and I noticed the transmission/hydraulics overheating. Oil levels were fine. It has a remote valve controlled by one lever. It appears the lever has three positions...

Yesterday I was cutting thick blackberry brambles and thick weeds and I noticed the transmission/hydraulics overheating. Oil levels were fine. It has a remote valve controled by one lever. It appears the lever has three positions up/float/down. I know if the lever is left up the oil could...

Are Simca tillers still imported and if they are do you know of any dealers? Thanks for any help.

Iam having a problem with the power lift on my CX Gator. It will lift the cargo box but when it begins the down cycle it hesitates and jerks but will eventually go down. I will appreciate any help you can give on what may be the problem.

I was servicing my 1401 Monday and before changing oil I let the tractor run until warm. As the oil was draining I checked the radiator coolant. When I opened the cap I noticed foam. The coolant was clear with no oil and the oil did not have coolant in it. I saw no bubbles but when the tractor...

I am considering a John Deere Z225 zero turn for trimming. I have four acres but I cut most of it with a 60 " finishing mower. The Z225 will be used for trimming in close quarters and some fall leaf pick up. What are the pros and cons of this model. Thank you for any information.

I tried starting my 1410 today (30 degrees F). The starter started turning the engine over and when I turned the key off to rest the starter the starter kept turning. I pulled a battery cable off. There was some electrical smoke and the cable was hot. Thank you in advance for your help.

My friend has a F22 that I believe the fuel selenoid is bad. I helped him start it last week by moving the handle on the side of the selenoid back and forth. It begin to buzz and the tractor started. Now, the engine won't do anything but turn over. Do you think it is a bad selenoid and where can...

Do any of you know where I can find parts Blades, belts etc) for a Masciho five foot finishing mower? Thanks for any help.

I have some difficulty in finding a new fuel transfer pump for the F22. Would an electric fuel pump work?

I have a JD rear engine rider with 13 hp Briggs engine that I use for triming. I bought it new in 03 and haven't used it much. The other day it started to miss and the plug was fowled. I cleaned the plug until I could get another. Yesterday it started and in about 5 minutes it started missing...

I need advice on a good hand held blower. I have owned two JD's that Echo made for them and they gave me good service. The only hand held model my JD dealer has is a 4 cycle model priced at $249. Thank you in advance for your suggestions.

I have a friend that has a F22D and this weekend while he was doing some loader work the engine began to sputter and stopped. He started it but it sputtered for several seconds and then straightened out but a few minutes it did it again. I checked the following for him: Air cleaner clean Water...

The front emblem on my NH 3930 has broken off two times. The emblem is a plastic oval that inserts into the top front hood. I guess vibration breaks the emblem studs. I know I don't need it but I am kind of particular when it comes to my equipment. Do any of you know where I can get an oval...

I have a friend in the market for a Yanmar 4X4with FEL. He has narrowed his search to the following: 1601D 1610D 1700D Since he has no computer he asked me to get the experts opinion. I have a 1401 and the 3 cyl. sure is quieter. I have been steering him toward the 1610. He will be grateful for...

I remember when the barns and ouit buildings were white washed with a lime/water solution. This left a chalky white coating. I am wanting to white wash a barn and I have the following questions: What are all the ingredients in this solution and the mixture ratio? I want to spray it on therefore...

Do any of you know a good Yanmar dealer in the west TN area? Thanks

The oil pressure warning light has quit functioning. I checked the bulb and it seemed to be alright. I switched the temp and oil light but still nothing. The fuse is good. Where do I go from here?

I am looking at a model TPH 122 Mackissic 3 point chipper shredder. I will be using it on a Yanmar 1401. I have found to dealers that carry this model one being Northern and the other West Power Tools. Both price the shredder at approximately 1650 however West ships free. I am wondering if any...

I have a friend that is looking for a grass catcher to fit a 16 hp 42 inch cut Scotts lawn tractor. He checked with the local JD dealer and was told the catcher was unavailable through their dept. Does anyone know where he might find one?

I was clipping pasture with a six foot rotary cutter and noticed the transmission building intence heat in fact there was smoke coming from the area. The grass was tall with areas of thick Johnson Grass however I was mowing in second gear. I stopped and let the tractor cool until the following...

I am looking at three brands of vacuum rakes Cyclone, DR and Agri-Fab. Have any of you had experience with these brands? They are all in the same ball park when it comes to price. Thanks for the help.

I am considering a leaf and lawn vacuum. I have looked at the DR and Agri-fab molels. Both have 5.5 hp BS engines. The DR is approx. $300 more than the Agri-fad. Which is the better of the models? Thanks for the help.

I have approx. four acres with two acres open the other has fruit trees etc. I have a tractor and five foot finishing mower and it is great for the open area but getting around the trees takes a long time. I am considering a residental ZTR. I don't want to go the commercial route because of the...

I have two 30 gal. fuel tanks side-by-side, one is diesel the other gasoline. I went to refuel my 1401 and inadvertantly placed the gasoline hose in the tractor tank. It was no more than a pint that entered the tank. I went on and refueled with diesel not thinking much about it. However I got to...

I am looking at a 7600 Agco Allis tractor with cab/air. The tractor is clean with 2400 hours. The asking price is 16,500. What are the pro and cons of this tractor and is this a fair market price?

My 1401 (2wd) has a shimmy in the front wheels when in high grear. It is really intense after the tractor hits a rough place. There doesn't seem to be much play in the steering. Any suggestions will be appreciated.

I have asked for help before on this machine. I brought new sprockets, bottom rollers, chain and pads. When the machanic was replacing the parts he found that the track tightening pistons were bad. Do any you know where I can get these?

I know that this has been discussed but I just have to vent. Last night when I was thumbing through a farm magazine enjoying the photos of new tractors which I can't afford and on page 12 was a full page warning paid for by Yanmar America. I naturally read it since I own a little 1401. I was...

I am in desperate of a cutter bar for my Mitsubishi BD2F. The blade is a hydraulic angle and is approx. 71/2 feet long. The bar is a three piece unit. There is a 20 inch section broken out of the middle piece. This section has ten bolt holes. I am looking for new or used. Thank you for any help.

I own a NH 3930 (tractor no. 042423B, ModelCA51WX, engine C636596 -96 or 97 model) that is equipped with an oil bath air cleaner instead of the more common dry type. I need the bottom bowl assembly with the sealing ring. The catches on the bowl that I have are broken. The NH dealer said that he...

Hey Taylortractornut, I have been trying to get in touch with you on the private section. Will you get in touch?

I own a Mitsubishi BD2F dozer. The dozer has a good engine and hydraulics. The undercarriage has new rollers but needs sprockets and rails. I have been told by several not to repair the undercarriage but to get what I can out of it and buy a JD350. They tell me parts availability etc. A good JD...

My brother-in-law just purchased a 1601 from an importer. It is very sharp with original paint etc. It is my understanding that this tractor has a three speed settings with the 1st the lowest three speeds, 2nd 4,5,6 and the 3rd with 7,8,9 and a reverse in all three settings. When I tried the 1st...

I know this discussion has been discussed thoroughly. I am torn by the DR or Northern. My budget will allow me to spend up to $2000.00. I was wondering about the pros and cons of both. I have an old Troybilt that I can both chip and shred. Are there other brands within my price range. It will...

I have a Mitsubishi BD2f dozer that I had a new undercarriage installed on the unit. The replacements consisted of new rails, rollers and weld on sprockets. The front idler wasn't replaced. The problem is that the tracks come off to the inside. I have had two opinions: The front idler is worn or...

38\" or 42\" finish mower Do any of you know of a company that manufactures 38" or 42" 3 pt finish mowers? Thanks

Will a Yanmar YM 1100 pull a 4 foot finish mower?

I saw a Yanmar GT14 diesel garden tractor on ebay. The seller indicates that it is a 1999 model. Could it really be a 99 model and has anyone had experience with a Yanmar garden tractor?

I have a Mitsubishi BD2F dozer with pyramid track pads. I put new chain,rollers and sprockets on the machine however the left track chain rolls up on the front roller and slips off. What is the problem and remedy? Thank you for the help.

I have read the posts concerning the Chinese models and the DR. Have any of you had experience with the Northern Hydraulic 3 pt chipper shredders? One costs approx. 1400 and the other 2400.

Need help! I need a water pump for a Mitsubishi 210D approx. 1983 model? Thanks for any help you can give me.

My 1401 has begin leaking around the rear axle seals. I am sure this has been discussed before but how difficult is it to replace the seals?

I have a friend who bought an antique grist mill that is operated by a belt. He has a Kubota and was wondering if Kubota built a belt pulley that attaches to the pto. I don't know model of tractor.

I was wondering if anyone on the forum can give me the date of manufacture of a Mitsubishi BD2F dozer ser:1B102855--41767. It is grey market. Thank you

Can anyone tell me where I might purchase an operators manual for a New Holland 3930 4 WD? It is grey market imported from Europe. Thanks

I have been loading and unloading tractors and dozers since I was in my early teens. My Dad and Uncle always stressed safety and I have practiced safety. However at a dumb age of 54 I was nearly killed in an unloading accident. Tractor-NO, Dozer-No, small JD lawn tractor YES! We were preparing...

I thought it would be a good idea to bring the issue of front weigths to this forum. I am sure they have been discussed in the past. I have heard of and seem photos of small Yanmars carrying at least 300# lb weights on the front. This much weight is extremely hard on the steering mechanism. I...

A few days ago I did a post looking for a tiller gauge wheel. I have found one however several people have told me that they have taken the gauge wheels off and control the depth with the 3pt. lever. I was wondering if I could get pros and cons of doing this from other Yarmar owners.

Do any of you know where I can find a gauge wheel for my Yanmar tiller? The wheel measures approx 12 inches in diameter. Thanks

I have a Ford 532 baler that is in good mechanical condition therefore I am painting it. Do any of you know where I can get decals for the baler? Thank you.

Where can I find a YM1300 manual(operators)? Aren't they the same as the US 135? Thanks in advance

I have a 1401 that I use for all my yard and garden work. I try to keep it in excellent shape . I have lost the plastic cover for the fuse block. I was wondering if anyone in Yanmar land might know where I might purchase one? Thanks in advance.

I am in the process of developing approx. 13 acres of bermuda grass for square bailing. There are several rocks on the property and this winter I will use a rock rake however I know I will not be able to remove all the rocks. My question is would a sickle mower or a disc mower be better? I have...

Do any of you vintage tractor collectors know of an insurance company that specializes in antique tractor and toy tractor collections? Your help will be appreciated.

I am looking for a head and manifold for a 1949 M John Deere. Any help will be appreciated.

I have purchased a Ford 2600 and I am looking for owners manual and both headlight assemblies. Any help will be appreciated.

Has any one owned a Ford 2600? What was your experience and what would be the value of a 1979-80 in excellent condition?

Do any of you know where I can get a hood for a STX 38 gear drive, black deck mower. The fiberglass hood brackets have broken. Any help will be appreciated.

I am looking for good used or new rubber tracks for a Komatsu D21A dozer. Rubber tracks are great for landscape work in subdivisions. The rubber tracks are completely worn and split. Any help wii be appreciated.

I have an Oliver 550 that I would like to install a ROPS unit and seat belt. Since Oliver never built a unit I was wondering if there is a company that manufacturers ROPS for vintage tractors. Any help will be appreciated

My friend and are thinking of sellingYanmars. This will not be a front yard operation. He has an ornametal welding business . The business has a large shop and paint room. I am nearing retirement as a college professor. He and I have farm and equipment experience. My folks sold Oliver equipment...

Earlier I posted a request for decals for my 1401. During the meantime I heard of a dealer that sold decals. I phoned him and was told that the decals were available. When they arrived they looked terrible. They were too narrow , wrong color and were generic(YANMAR DIESEL). Yhey wouldn't even...

I need help in locating a headgasket set for a D2050FD. Any help will be appreciated.

I need information concerning placing a belly mower on my ym 1401. Is it possible? Where do I find the adapters etc? Have any users ever put a belly mower on the 1401? Any advice will be appreciated. Photos would be extremely helpful. Thanks in advance

I have a 1401 with a hydralic problem. The lift works but when the lever is at the neutral range(mid-way) the lift will not hold. I knoe that there will be some leakage when the tractor is not running but this problem exists when the tractor is running. I have already experimented with the side...

I would like to inquire as to how the power shift 1610 operates. I am familiar with hydrostatic transmisons and partial on large JD and TA on CI. Thanks

Do any Yanmar owners know where I can find hooh decals for a two wheel drive Yanmar 1401. I can get decals with just Yanmar but I would like the model number on the decal.