Search results

I bought a 773, maybe a 2000. It has Keyless start and is unlocked right now. I have a Master code, but need help setting an operator code. I can't seem to find anything out online, as far as the procedure for setting it.

I'm considering letting go of my 60" harley rake, since I don't get to use it much. Actually, I don't think I used at all other than trying it out. It's been completely rebuilt to new condition with new chain and sprockets, bearings, paint, etc. I'm not trying to sell it here, I just wondered...

5' harley rake 3-point attachment. Like new condition. Completely rebuilt. Brand new drive shaft and clutch, All new pillow block bearings. transmission has all new sprockets and new chain. New tension springs. New tires rims and bearings. Repainted Kubota orange and gray. Only thing missing is...

While restorting as harley rake I decided to add a slip clutch because of the damage encounter by rollers jamming, chain jumping sprokets and pillow block bearings breaking. As I was removing the old coupling from the gear box, it had a friction clutch. I never seen one before. It had springs...

Ever see a slip clutch mounted on pto of tractor??... right at the tractor? I picked up a Harley rake and it has no slip clutch. Right on the PTO might be the easiest place to add it.

I want to install a slip clutch on a Harley rake. I think the best place would be on the gear box input. I have a 1" keyed shaft on the input gear box which the drive shaft connects to now. All the clutches I see have 1-3/8" fittings. How can I go from PTO Shaft to clutch then to 1" keyed...

I was looking a a Scag Tiger cub for sale The guy says it's 4 years old. It has a 26Hp B&S 3600 hours. He wants around $3500 for it. Does this seem like a lot of hours for 4 years?

I need to have less retraction on my grapple cylinder. For example if my pin centers are 16" when retracted, I would need the pin cylinder to be limited to 17". How can I do this?

When it closes, It ends up ripping the grapple frame apart if I hold the valve too long. It's a 2 1/2" cylinder and I need a pressure relief valve. Put I only want pressure relief on this cylinder only. How do I do it?

I have a hydraulic cylinder for my tilt. It has a 1" swivel end and my bolt is 3/4". I can't find a 1" to 3/4" reducer. I would even buy a new top link bolt that had a 1" end as another option.

I suspect a woodchuck. I have seen one around. I have a fence, but he maybe getting through. How do I get rid of him, no guns there are other houses around.

Tilt cylinder control valve I was going with electric over hydraulic, but know I am changing plans. I would like to select a single valve for my L3400. Tandem center valve, single spool. Any links to a valve would be great. Does this look right...

I bought a side link cylinder from SC with Sae 8 ports I need a 90 degree fitting into 1/4" Hydraulic hose.

Kubota L3400 Where is a good source for a tilt cylinder? Can you even buy a cylinder made up with the proper ends or do you have to make your own? What is the Bore and stroke?

I have the woods 750 BH now, but I have a line on a woods S9000. My front and rear tires are foam filled so I have weight. (foam is heavier than calcium filled tires...go figure) Just wondering whats the smallest tractor that this wood s9000 can go on. The woods weighs 1300#, I don't know what...

If anyone has either a King Kutter or Dark Horse tiller ( Basically the same unit other than color and assembly) and is leaking oil, then I can help you with the fix. Seals are $5.00 each. Breaking tines? If anyone needs help through the process, I would more than happy to help! I have done...

Markham is out, they don't answer phones, return calls or e-mails. So I am looking into making my own. Now has anyone have any experience with either of these teeth? the A-175-1 or the case 23 series picture shows the shank only.

Does anyone else txt while driving the tractor?

While I'm waiting for Markham to answer e-mail, I thought about making my own toothbar. Where can you buy these teeth. I checked ebay, but can't seem to find any. Any teeth sources?

I want to do a Inside drain around the basement perimeter but I can't find a source for WaterGuard.

I can't seem to get the ground flat. (See little mounds in pics) As I pull the rake, the material will build up, then as the material gets too heavy it dumps or the rake lifts over and creates a mound over and over as I go. The same thing will happen with a box scraper. These are great tools...

How can anyone function without a welder? I was thinking of driving an hour to TS to buy sweeps, but these larger cultivator sweeps angle the wrong direction.(according to me) I need them to get after the weeds. So I made my own with a small piece of angle welded to the tip. These tip are all...

I had a bad twist. So I cut out the twisted section. Welded a new section in with a piece of rectangle stock. Then I also sleeved the pivot point while I had it apart. Then I did a lousy orange paint job on it. I kill everything with a lousy paint job.

I posted my Tractor price I paid on a thread a month ago. Where is that thread that had average pricing on it of all the models?

I am looking at Markham vs Yankeewarehouse. Does the Markham teeth postion the tooth lower than the bucket? When your bucket is level, is the tooth below the bucket? It seems like Yankee TB puts the tooth level with the bucket. Maybe making finer clean up possible. Please posts a comment if you...

I picked up a 60" tiller today "DARK HORSE" It was returned to the dealer because of an oil leak. A little deal(liiitttleee deal) and I was loading it up. The tines were slightly worn, but in perfect condition. It had seen some usage. Other than dirt and oil on the seal, it looked like a new...

I am getting close to pulling the trigger on a TSC tiller. The store has it for $1549, I have a 10% coupon= $1394.10 plus tax.=$1477.46 Is this about right?

I was looking at the county line tiller at the TSC web site. I noticed some tillers can be reversed, how is it done? Tractor Supply Company - CountyLine Tiller, 60 in.

I have a L3400 and I from reading different threads, I sure I want a reverse rotation tiller. I will be doing light gardening work and maybe a small patch of lawn here and there. I saw the TSC 60", but I don't think it's reverse rotation, unless it can be swapped. I am looking for advice in...

I wanted to put in a bigger garden this year with my new bigger tractor. Let me rephrase that........................ I want to put in a bigger garden, because I have a bigger tractor. I used a rototiller, I noticed the lawn was wet. Then I pulled in a trailer with manure and the trailer wheels...

I used a QA plate that I use for my forks and put 3-point attachments to speed things up. If I have the backhoe on at a job and I need to clean up with bucket and york rake. It's just a flip of the QA arms. I don't need to remove the backhoe Another big advantage is down force. I can give my...

I asked this question before, but I see different things now. (I see dead people)..... just kidding. My loader arms seem to go up uneven. I first notice the touch down on the bucket was about 1" off from side to side. I thought the tractor was not level. Now I see when the loader goes up the...

I'm not really sure which attachments to use to convert a beautiful established lawn into a garden area....... area is 40' by 40' This is what I have for attachments. 1. Backhoe 2. Box grader with scafires 3. Middle buster Now I have access to a tiller, but I would have to ask a friend and go...

Work is slow and I needed a project, so I decided to build a cab. I needed to keep the overall height under 81 inches to get into a garage. I used an old squat rack someone gave me. I made two loader brackets and painted them orange. Next I made a windshield frame. Then I made rear supports. I...

I wanted to make a snowplow for the tractor, but tractors have no suspension and when run on uneven ground, the blade digs into the asphalt. I made a blade with a swivel mount, so it will follow the contour of the driveway and not be married to tractor suspension. I will use the electric over...

I noticed my loader arms put the bucket down on a slight angle. One side hits the ground about 2" before the other. The bucket is 66" so the error is multiplied out from the arms. Kubota L3400, 8 months old, It was like this since day 1. Is there anyway of making it straight?

I been looking at the grapples that attach to buckets, but I have a quick attach bucket on my Kubota L3400. Drop the bucket and put on forks. None of the grapples were made to do what I needed, so I made my own. I bolted square tubing to my loaded arms, The grapple slides into these square...

I just completed my grapple install. I used a 12 volt solenoid open center, spring centering valve mounted on a DO3 sub-plate. The grapple drifts rapidly down as soon as power is removed. If I quick disconnect the cylinder, you cannot move the grapple, so I would say cylinder is fine. Could...