3-point

I need to rent a post hole digger and the rental company is not familiar with the LX 2610. He said that the auger may need to be started at a slight angle depending on the height of the tractor. It's a IronCraft 3-Point Post Hole Digger - PH Post Hole Auger | IronCraft | Tractor & Skid Steer...

I am new to the forum; so don't really know how to participate but here goes. I have own a Branson 3510i for a few years. Bought it used from a friend. Everything worked fine. A couple of days ago the bush hog came all the way to the up position and has stayed there except when the engine is...

I'm looking for a replacement/improved version of the side-tensioner for my 3point hitch. I'm finally getting around to installing my weld-on Euro hooks. It will be fantastic to finally have quick hitch - and just in time as I happen to have a lot of implement I'll be doing this spring. I...

I recently sold my home on a mountain in the Adirondack region of northern New York. For the last twenty years, I maintained a steep, winding 2,400-foot drive with a 30-hp Cub Cadet Compact tractor, which had a 7-foot ABI rear blade and a 5-foot bucket. I let the tractor go with the house. I've...

I am looking for a decent 3-point set of forks. My application is to leave my front-end loader on and be able to haul some tools (shovels, chain saw....) along. I wouldn't mind if someone had a ready made "basket", but I have not seen one ? So, will construct my own pallet to use. I see prices...

My tractors 3 point lever is labeled 0 - 10… with 10 being fully raised… Problem is, between 0 and 7 nothing happens out back… so 7 thru 10 is the range that raises/lowers the implements… rather abruptly… I’ve watched the lift arms without anything attached… nothing happens… so it’s not the...

This is fun; after spending some time with the box blade, pushing and pulling, the 3-point has taken upon itself to not lower. I checked all the physical links between the control lever, I adjusted the drop rate in both directions repeatedly, I've taken the seat off and inspected what I could...

Has anyone ever tried putting a 3-point hitch on the front of a compact tractor and using it to mount a back blade to plow snow? -- I know there won't be any springs to dampen the blade hitting something, but my drive way is short and there are no curbs to hit. Just wondering if this is a...

I am having a hard time adjusting the top link on my Kubota. I loosened up the locking nut but I was not able to turn the adjuster. I suspect these (2) screws on the adjuster could be also locking pins? Could someone tell me what these are and whether they need to be loosen up before attempting...

Hello, A friend recently offered to give me a Massey-Ferguson sickle bar mower that has been sitting in his field for the past few years. I looked at it and it has only surface rust and is in good shape, and It would make a nice addition to my small collection of tractors. However, the only...

[this subject is on a 1986 Ford 2110 fwd/diesel] So I am changing lout the old and tired 2-spool valve, to a new 3-spool. Of course, I didn't have all the parts on hand mostly because my working on tractors knowledge is limited to the past few years. Anyway, I checked the fitting and...

Greeting all, Just joined and I'm hoping to get some help or at least pointed in the right direction. I have a 1998 Fermec 650 and the 3-point hitch is not raising. I had the hydraulic lift piston replaced and still not raising. Ideally I would like to be able to track down a service/repair...

I just figured out how to add a rear 3-point lift control to the back of my RK25/TYM T25. I think this may work for most tractors: if you like it, please comment and subscribe! Thanks for watching!

The overall width of my tractor is 6 feet. I am intending to buy a land plane/grader for driveway maintenance and general landscaping and I'm looking for opinions on whether a standard 6-foot grader is adequate or if it's best to go with a seven-foot grader for coverage outside the tractor...