control

I have a TYM 2515H with a BL 150 loader, tractor has 21 hours. Scooped some dirt, dumped it went for the next scoop and now the control lever is frozen. Bucket will curl and dump but the loader will not raise or lower.

I bought from my local KIOTI dealer, and just installed, the factory cruise control kit for my 2018 Kioti. The dash light illuminates when I press the on switch, but when I release it, the light goes out and the FWD pedal returns to neutral setting. The manual is confusing, but I also tried...

I maintain 1.25 miles of private gravel road. The dust is just terrible in some spots where houses are close to the road. I used to spread calcium chloride, but the prices are getting out of hand. I looked into millings and oil & chip, but those prices are way too expensive as well. Yes, this...

So my woods was partially logged right before we purchased the property 19 months ago. The woods is absolutely invested with briars, weeds, and saplings. Is there anything I can spray on this that will help control that overgrowth but not harm the trees? It’s a large area so I would want to...

It all started when my wife said that she wanted to get a "Show" quality Akita puppy and start going to dog shows. Several years later, and several dogs later, we now have a stainless steel dog bathtub. It was only $2,400 and Amazon is letting her make 6 equal payments without interest. I...

Hey folks, I finally broke down and bought the cruise control kit for my l3301 hst. The parts diagram was all I had to go by, and before I put the right floor panel back I tried to test it. When trying to test, it seems like the brake pedals weren't engaging the line to kill the CC. Does anyone...

Is there an adjustment for the joy stick for when it is in the float mode? My joy stick is difficult to pull back and has quite a loud snap when it releases from the float position.

i have a DigMaster 200 which is a Rippa 328. (I posted under Rippa because the Digmaster just come out and not many out there) I just got mine and I just cant operate it using the excv. controls. I had a JD excavator and backhoes and at at 84 you are not going to reprogram my mind. To me it's...

I'd prefer to have a manual transmission...but everything is automatic now. My current 2011 F150 with 6R80 has "M" on the shifter. Using "M" the transmission behaves like a powershift tractor with instant, firm shifts, up or down, when driver wants using +/- Looking at 2020+ model year...

Hi i have a massey fergason 65 multipower tractor The hyd valve that worked 3 point linkage then could be swapped to hyd hoses at rear leaked badly and cannot be fixed Has any one used an aftermarket assembly to replace the old one, Has anyone used this unit or is there something else that...

I took my u48 in last fall before warranty was up to get a small pilot control leak fixed. It is very small, they thought it was an oring but I guess it’s not. I’ve traced it to the #4 hose but instead of being the quick connect it looks like it may be the hose crimp. Still watching it but it’s...

I have a JD1050 that the previous owner fitted with a ezee on front end loader. To do this they added on a hydraulic control valve that is similar to the below image. I would like to use a grapple on the loader and need someway of adding a third function. I could add a valve and "steal" flow...

How do I set the bottom and top limit on the automatic lift control. I currently set the lower limit with the manual 3pt level. When I use the automatic lift control to raise the three point hitch it only raises about one foot instead of the full height. Am I doing something wrong?

I am building a roll-off dumpster truck. I would like to control the bed lift from both inside the cab and outside. Is this possible? Do you all have any suggestions on which setup would be best? I plan on mounting either an engine-driven pump with a 12v clutch or a PTO pump. Both will have to...

I have a new to me ck3510 se/c HST because I couldn't afford a CK3520 that already has the rear lever to control the 3 point while connecting implements. Has anyone ever made this modification? I always wished I had one on my open station Kubota and now I really want one on my cab model.

I have a Bobcat CT 2040 tractor with a loader. The issue I have is that there is a very small window on the joystick valve for slower, more controlled bucket lift / lower or tilt. It is especially bad when trying to gently use pallet forks. It is a very tense, 2 handed operation. I don’t want a...

Hello. I have a 2019 4044R with 610 hrs on it and the ground speed and cruise control are not working now. No light comes on for cruise when pushed. Wondering if anyone else has had the same issue? And if so what the fix was. Thank you!

It's on my SIL's little Kubota B1550, but may apply to any brand. The issue is he has to hold the lift controller up, or the lever just goes to the "lowering" end. There's no tension on the lever, only has a movable "stop". I can't find any missing parts or tension adjustment, but this...

I think it's a 2020 model but not sure. But new to me. I had and still have the Kubota 2230 but got it didn't have fel. The SA221 does. In any case teh question I have here is the rear left control operation. I know it doesn't have position control, but the up/down is difficult to get out of...

Has anyone else thought it odd that the PTO monitor lamp is on the right side of the instrument cluster, above the cruise control rocker switch; and the cruise control monitor lamp is on the left side of the instrument cluster, above the PTO rocker switch? To me it would make more sense to put...

Doesn't everybody have them? I see runs dug up here and there. Sometimes they wash out in a heavy train and act like drains that cause problems down hill. But I have some areas that see like they got lost and went around in a maze pattern tearing up several square yards of lawn. If you step...

I've got a Woods 15' Batwing cutter that has served me well for a bit over 9 years now. But It's showing some deck rust. I blow the deck off daily when using the cutter, but the corrosive nature of plant fluids makes it's way through anything after awhile, and factory paint or powder coat on...

I have been using a 1/2HP submersible in this well since 1976 to irrigate our 1/2 acre of fescue and it has never failed to deliver at least ten GPM. We've had a couple years of drouth in NCKS and the well responds saying I can deliver the ten gallons but absolutely no more and the pump will...

Have a 2008 GC 2610 MF the speed control well not engage. I have cheeked the cable and it moves freely. Cannot find any information on this problem. Any suggestions will be helpful. Thanks

I have a BX2200 that is leaking around the control arm for the pto at the transmission. I'm trying to remove the control arm to replace the o rings and have removed the bolt that goes thru it and the shaft and it will not come off. I don't see anything else holding it on and the service manual...

I’m looking at adding rear remotes to my L3240 using a Summit Hydraulic remote kit to supply top and tilt cylinders. The summit kit includes a T connection to return to the tank. Is the T connection really necessary for top and tilt (2 way) cylinders? I have a W R Long 3rd function valve...

Hi! I have an old Ford 1700. Recently, the control arm for the 3pt lift has been "slipping" up. Messing around with it, it goes down with resistance, but when I pull on it, it moves pretty easily, which means if you hit a bump, it will lift the 3pt arms, which makes grading really annoying...

I built about five years ago a fire wood processor that is run by Hydraulics. The processor has a 30" chainsaw bar with a 404 chain on it. I have a hydraulic spool valve that has an open center that is hooked to a hydraulic cylinder. The cylinder is hooked to the 30" chainsaw bar. This is what...

I know this is old news, but $540 for a tie rod and $80 for a hub oil seal?!? I'm going to have to roll the dice in the aftermarket.

If anyone is looking for a fix of the control valve ball and socket and you have some basic mechanics skills please follow the link. Maybe a moderator can combine the threads and sticky this. https://www.tractorbynet.com/forums/threads/ls-lb1100-backhoe-control-valve-issue.468128/

Does anyone have a suggestion on how to prevent the joint rod end from slipping out of the control lever on a LA463FL? I replaced it and it works for a brief time and then slips out, usually when lowering. I left the cover off and observed it and it even will slip out with the bucket lowered...

Hi everybody, We built a new -heated- workshop, nice! But it is much warmer at the ceiling and mezzanine than on the floor. I guess it needs some kind of fan Trying to find out a way to turn it on as needed. It seems a bit much to let it run all the time. Compare top and bottom temperatures...

Tym 330 HST - stock FEL controls / joystick. When I open the bucket and release it sticks open, does not spring back as it used to. Bucket keeps going to open - rolling back in toward tractor. Took off boot on joystick, everthing looks intact for the actual joystick, its just not...