fitting

  1. O

    tapered/NPT -vs- straight/BSP - is BSPP worth the cost?

    In another life (work $ + robustness requirements) we would go BSPP 100% given the choice. It's a better design, relying on the elastomeric seal is generally regarded as being much more robust than relying on sealant and thread deformation. Custom hydraulic work, on my own, is new to me...
  2. A

    Tym T394 Jerk Fitting Size

    What is the Zerk grease fitting size on a TYM T394 tractor so I can by a tip for my grease gun to fit?
  3. B

    Female Hydraulic Fitting Won't Lock On the Male Firring

    Almost new tractor and I don't believe the remotes have even been used. Went to hook them up and one female won't accept the male fitting. One works just as it is supposed to but the other one you can't get the male into it far enough for the detent balls to engage. It is definitely that...
  4. H

    Hose Fitting Sealents

    I've read some say only use pipe joint compound on threads. Is there a special hydraulic compound or will any brand do? The Oatey ordinary plumbers pipe joint compound I have says good to 10K PSI with liquids. What's the consensus on the yellow teflon tape made for contact with gasoline and...
  5. S

    rubber hose fitting for hydraulic pump

    low pressure hydraulic pump rubber return fitting for Branson 2910i
  6. C

    Help with a grease fitting Kioti 3510

    Hi I have a 2019 Kioti 3510 that I am having an issue with a couple of the grease fittings on the loader. It appears as if grease is coming out the side of the fitting when I'm filling it. I've attached a picture of one fitting and circled where the grease is coming out. What causes this...
  7. charlessenf

    Which fitting should I dislodge first? (Dirty Hands WS)

    OK, the reason Dirty Hands Brand is no longer literally 'popped up' this morning when the entire weld (24 =/- inches) let go all at once. Based upon the condition of the parts the weld was never done properly and there was no evidence of PENETRATION along the length of the break! So, I have to...
  8. 2515R Dude

    What size O-Ring for ORB fitting

    Another stupid question, searched everywhere, cannot find and answer. I have a 27 Ton splitter and it leaks at two connections on the control valve. One is 1/2 ORB (3/4" thread OD) and another is 5/8 ORB (7/8 thread OD). I went to NAPA at least three times to buy correct O-rings. Whatever they...
  9. C

    Hydraulic Fitting Style???

    Will ask same on M-F forum, and did so on hydraulic forum... Need to pull engine and steering cylinder on my 1440V (rusting under chrome plate of ram) so grabbed a JIC 3/8 cap and plug. Duh....they don't quite fit! What standard are the hydraulic fittings made to? BPS???? and if so, why??
  10. G

    Loader Fittings ID

    Hi All - first post here, been lurking for a while. I've been fitting a Hymari FEL to my Iseki TX2140 Compact tractor. I'm completely stumped by the hydraulic fitting on the loader spool. Can anyone help me ID it? Cheers Andrew
  11. N80

    Wood working:Dry fitting?

    I wouldn't say I am new to woodworking. I've made several nice looking but not fine built-in shelves for my house that turned out very well. All painted, not stained/finished. These were all using bought lumber. No serious joinery. I am currently making a set of shelves from white oak off of a...
  12. Balazar

    Help me identify this fitting.

    I bought a grapple at an auction. Seems to be foreign import. It came with flat face couplers. I want to put Pioneer couplers on it. What in the world is this and what is the most simple solution to switch to Pioneer? The out of focus 90 fitting has the an adapter in it that adapts it to...
  13. C

    Brass fitting safe to use with diesel

    Branson 3510i, plastic nipple on the left side fuel tank broke off from the tank. Dunno how it happened...guessing snow/ice chunk might have caught it when I was snow blowing. Anyways, got the tank removed and looking to make a repair. Was thinking I'd drill the hole out, tap it/thread it and...
Top