ford 1310

The information I've read calls for 52 KG torque readings. Isn't that over 100 foot pounds on a 8mm head bolt. I pulled them down to 50 and decided that was too much for an 8 mm head bolt. Could some one give me the proper torque values. Thanks in advance.

I had a bad case of seat-base metal fatique/cracking on my 1986 Ford 1310 and did a repair & slight reinforcement using a MIG welding. It worked out great and looks perfectly OK for a tractor seat base. Item 50 above (base) alone is not available from NH, instead you would...

I have been using Universal Hydraulic oil (meets Ford 134 spec) in the transmission, hydraulics & front axle just like the manual recommends, but have been wondering if I should switch the front axle to 85W-90 GL 4 or 5 gear oil? The 134 spec oil is pretty thin for the front axle and leaks...

Hi There. My first post. I took the steering box apart on my Ford 1310. The end of the sector shaft that holds the adjustment bolt is broken. I have been searching for a new sector shaft or steering box everywhere and can't find one. Does anyone know if another shaft from a similar model will...

Hey Guys just wondering what yall thought about each of these. The Ford 1310 is mid 80's a little rusty 2wd turf tires 500 or so hours. The Massey 1210 mid 90's 2wd turf tires 700 or so hours. Curious about getting parts etc. Which would you choose and why? Thanks

It痴 rather embarrassing but I can稚 figure out how to shift my Ford 1310 tractor in to reverse. I even purchased the operators manual but it doesn稚 specify how to shift it into reverse either. I have the main shifter on the steering column and the gear shift diagram only shows 1-4. I致e tried...

Hi all- new member but longtime reader. Happy to have finally joined...my tractor is a circa 1986 ford 1310. Take care and can稚 wait to pick the brains of some of you experts and old timers!

I have an old Ford 1310 4wd tractor that is in need of new R1 tires front and rear. The problem is that it doesn't have the original rims. Tractordata.com lists the original tire sizes for the front as 6.00 x 12 and the rears as 12.4 x 16, but I currently have 6 x 14 on the front and 9.5 x 24 on...

Does anyone know if you can retrofit a E673L Shibaura engine into a 1310 Ford? It currently has a S753 engine in it. Any infomation source or guide material on engine swaps for Shibaura engines?

Hey everyone, first time poster here! I recently inherited a 1310 that my grandfather bought new. The steering gear box on it is SHOT! Can anyone point me in the right direction to find a replacement so I can return it to its former glory? Thanks for your help

What engine is compatible with the Ford 1310? It currently has a Shibaura S753 engine. Can you use an engine from a 1510, 1710 Ford? What about New Holland 1215?

I have a 1984 1310, manual steering with a loader, that is too big for the tractor. Well, the steering box is severely worn and upon inspection there is no lower bearing or bushing for the sector shaft. The shaft rides on the case itself. Is there a way to rebuild the box? A better solution...

where do I find the hydraulic screen filter for this tractor & why would the pto not work after it gets hot?

I need a diagram of the front end of a ford 1310 4x4 tractor.please help

hydraulics for front loader and rear lift do not work in extreme cold.

Hello, In need of some advice on the steering gear box on my 1310. The sector shaft has all the teeth broken off and the sleeves in the case are really worn. Anyone know where a guy can find the parts needed? The part number for the shaft is SBA334130040. The only one I can locate is...

Hi Folks, Well, I am in need of some guidance. We are in the snow here today, maybe 21" right now where I am. I was working it and I lost my 4 WD and realized that the main plate behind the front pumkin broke from the welds. I was not doing anything major at the time. I nursed it into the...

I have a mid 80's 1310 that we inherited. It has and FEL that has worked o.k. while I've owned it. I don't use the tractor a whole lot, but over the past 2 years or so the FEL has gotten more and more sluggish. I was told once that the controller most likely needed rebuilt. Last summer while...

3 point wont raise when warmed up

Purchased ford 1310 diesel 2wd tractor and did not receive operations manual at time of purchase. Looking to find out if a dual remote hydraulic system can be used on this machine. If it can, any suggestions where to find/purchase the remote. Looking to put a woods stump grinder (3pt...

I have a 84-86 year ford 1310 compact tractor and I have a question about the proofmeter or tachometer cable and what it plugs into on the far end from dash panel. It had been acting spradic especially on them cold days. It would show the tachometer needle jumping all over the gauge and...

Hello, I am replacing the small spring on the end of the high rpm screw that is located in the block just below the inj. pump. The small spring coils itself onto the adjusting screw. Should the spring coil onto the screw so the end is flush with the end of the adjusting screw? There is no...

I purchased a used Ford 1310 utility tractor. Right below the seat there is a lever that has a setting up and down. As I did not get an operating manual, I have no clue what this lever is for. Anyone help?

Took the loader off my 1310 and now the lift is not working, probably got air in lines, I think I should open the large return line at the pump to bleed the lines, is this correct.

I recently got a 1985 ford 1310 for next to nothing, it came with a new long block recently installed but it would only idle, so i took the timing cover off and played around with the govorner linkage and now it starts up and u can set your no load rpm say 2500 rpm, but when u apply a load it...

Name: Bob Kern I bought a 1310 Ford with a blown clutch. The throw out brg had eaten out the three fingers on the pressure plate.The bearing was NOT froze up. I have since replaced the clutch assembly, twice and it has done the same thing within 25 or so hours, both times. It had plenty of free...

I just acquired a ford 1310 and the rpm gauge does not work. How do I go about troubleshooting the problem and repairing the issue? Thanks

Hello all. Im new to this forum. I have a ford 1310 4x4 tractor with 13.6/16 turf tires. I am trying to find ag or industrial tires and rims for the rear of this tractor. According to the manufacturer that is the only tire capable of fitting on my rim. The tire size that they say fits is 12.4/16...

Hi, I have a, formally very reliable, 1984 Ford 1310. It has always started without issues. I started it today, no problem. Turned it off, ate lunch, came back turned the key, it made clunk (as if the starter was engaging), then nothing. Charged the battery, check the connection on the...

I have a mid-80's Ford 1310 with a 3 cylander diesel. I let my Father-In-Law borrow it and he took the liberty to change the oil, oil filter, and pressure wash the entire engine. Thanks, right? Wrong, it came back and doesn't have any power. He claimed it was because it needed the fuel filter...

Hey guys, im new here and searching for answers, i have just rebuilt my engine, and i cannot get any oil circulating, therefore no oil pressure, is there any way /or need to prime the oil pump, it worked fine before i rebuilt the engine?

How much longer can we expect support of the Ford line of tractors with the Shibaura engines? Most seem to go back to the 70's. I think Shibaura and Ford have called it quits or are about to. Just wondering if purchase of one of the Ford/Shibaura tractors is a good idea now.

During the initial start-up of my Ford 1310 three (3) cylinder Engine, the engine runs rough with a knocking noise. After about 5 minutes the engine smooths out like nothing was wrong... Any assistance with this problem would be appreciated...Chief

My RF wheel would not turn after a recent cold weather episode. The Temp had been very cold. (about -5F) I put a forced air heater on it a few minutes and rocked the machine back and forth. It finally broke free without any bad sounds. Nothing seemed to be dragging or clanging after it...

Can someone tell me what type and how much lubricant I need for the Manual Steering Box on my Ford 1310 tractor? Local dealer is closed today or I'd just call them. My manual does not have the info on the page that the description says it is on and I've not been able to find it anywhere in the book.

Sorry in advance for a long story...! so i have a ford 1310 that i got from a friend after the clutch went out on him, or so he said. we pushed the tractor up on his trailer using his new tractor. i got it off by parking on a hill and carefully rolling it off. the next day i started the...

Hi, my mother-in-law has a Ford 1310 tractor that runs fine, but the transmission is stuck in low gear. I can shift it fine through first through third, and into reverse, but I am unable to move the range of the transmission. Has this happened to anyone else and could you give me some guidance...

new guy here on search for the most economical soure of engine parts for shibura s753 3 cyl diesel. need pistons, rings, inserts, vale stem seals, gaskets, rebuilt injectors, glow plugs. the tractor was run dry of fuel, not by me. after i got it bled it was awfully hard to start. after start it...

HI!! to everyone. Put this post on the Ford/ NH owning and operating post and am not getting any replies, so I thought I would try here. I am a newbie owner of a 1984 Ford 1310, 4WD with FEL that I just purchased off of E-Bay. I am looking for any info I can get on maintenance and getting...

HI!! to everyone. I am a newbie owner of I 1984 Ford 1310, 4WD with FEL that I just purchased off of E-Bay. I am looking for any info I can get on maintenance and getting parts for the machine. I have ordered the I & T shop service manual, but have been unable to locate anywhere to get a...

I am thinking of buying a 1986 Ford 1310, 4wd, 770B FEL, 800hrs that is in excellent condition. I would like to be able to maintain that way. I would appreciate any links or names you have to offer for parts, particularly engine and trans/clutch. Jim Charlottesville, VA

If you can give me some feedback on a Ford 1310 I would appreciate it. Model: 1310 4WD Year: 1986 Make: Shibaura Engine Information No. Cylinders: 3 Displ. Cu. In.: 58 No. Speeds: 12F-4R H.P.: 16.50 Approx Shipping Weight (lbs): 2262 The tractor and loader are in immaculate shape, 800...

I want to sell a Ford 1310 4wd with loader, but I am not sure what price to ask? I think it is a 1985 model with 700 hrs. It runs great but cosmetically looks average (faded paint and small rust patch on hood). The previous owner did not keep it covered. I was thinking of asking $5000. Does this...

Looking at Ford 1310,750 hrs, FEL, 1984 (I've been told). Any info would be appreciated. Looking to clear wood lot and plant wildlife plot and make trail system thru property. Size okay for wants?, engine hp, PTO hp, big enough to run wood chipper? Any info would be apprecited. Far price would be ??