ford-new holland 1925

Hi, I've got a 1997 new holland 1925. It's a hydrostatic, with a 7308 nh loader. I've lost my hydraulics to both the bucket and the three point. Does the hydrostatic transmission use a seperate pump? Tractor still drives fine. I read a few threads on the divererter block and tried turning that...

Just put a repaired front end loader arm (leaking seal) back on tractor. Added hydraulic fluid to replace leak losses. New oil and oil filter. Level shows perfect on dip stick. Shred for one hour this morning and high temp light comes on. Stop engine and wait an hour. Went to replace...

Hello, I am looking to purchase a loader for my 1998 Ford / New Holland 1925 and want to get thoughts on which loader would be the best to purchase. I have been looking for about two years for the factory 7308 loader that was specified for the tractor but trying to find a decent one is...

Hello gents, it has been a while but I have had some long term problems with my 1925 FWD that have gotten bad enough that now I need to address them. My steering column is leaking power steering fluid from the little plastic plug under the steering wheel. I believe that many of these were...

Hey guys, I changed the hydraulic oil and filter on my 1929 hydro and now it has air in it. Bucket jerks up and down, same on 3 point. Tranny is hard to get moving and makes a funny vibrating noise when I take off forward. Any help is appreciated, never had this happen before. There is no oil...

Folks, anyone have the part number for the pull shutoff cable? I tried ordering one off Amazon and it was the wrong one. I don't have the patience for getting the wrong one again. I looked around for the parts to make my own or to mod the one I was sent, and no luck. Thanks!

Hi folks. I have a 1925 and the threaded inserts that hold the under-dash cowling on are either gone or spinning. The bolts in the middle can probably be drilled through and a nut put on the back. But the ones that hold the cowling to the firewall I have to fix differently. Anyone had luck...

OK, so this has been a great tractor since 1999. However, it seem to get progressively harder to operate the three point lift, especially when my shredder is attached (heavy). The lift lever is super stiff and not smooth at all. The front end loader lift works very well though. Is there...

Hello new member and a few questions about a 1925 that is for sale. Great site by the way! It has 767 hrs on it and a 60" or 72" mmm for 9k. From the pictures it seems to be in very good shape. It is about 2hrs for me to drive to look at it in person so i havent been able to check fluids or...

I had been having trouble with my tractor overheating after 45 minutes to an hour of shredding. I recently flushed the radiator and put a new belt on the tractor. Today, after about an hour of shredding, I stopped to clean the radiator screen as it often gets full of seeds and such. This...

I was tilling my field as usual when I raised my 3-pt hitch for the 5' tiller all the way up and the PTO lever kicked out of drive and then the PTO shaft started to leak fluid at a very fast rate. I think i was significantly over the 25Deg angle limit from the tiller operators manual. I did not...

Hello, I recently purchased a HST 1925 tractor with 7308 loader. The tractor did not come with any operators manuals but the operation and controls seems pretty straight forward and everything works. Before putting it to work I am changing all the fluids and filters. When I went to change the...

Does anyone no of a aftermarket stackable remotes?

A dealer close by has a 1998 NH 1925. 900 hours. Asking $12,800. The tractor is currently on Tractorhouse. What do you guys think of the tractor and model? I know NH only made them for 2 or 3 years. I'm shopping for my first compact tractor and can use all the help i can get.

I have been playing with my new toy , but for the life of me I have no clue what the pedal on the left is for . I am guessing it is the clutch . But its a hydrostatic machine . Maybe for the 3 point ? I am also curious if the hydrostat is seperate from the hydraulic oil?

Got the Nh running great , now I am torn between a 5 or 6 ft rotary mower , A 6ft may be tight on my trailer , and may be a bit big. I have a line on a like new JD rotary mower for $ 400 . I will be cutting a variety of sites and conditions. Opinions / recommendations

Hi all, I have been reading this site and there is a lot of good information here. I currently have a Balarus 562 that I believe I will have sold this weekend. I really haven't had any problems with it but it is too large and awkward for want i want to do. I have 180 acres and i lease out the...

Hi all, I have been reading this site and there is a lot of good information here. I currently have a Balarus 562 that I believe I will have sold this weekend. I really haven't had any problems with it but it is too large and awkward for want i want to do. I have 180 acres and i lease out...

New member here from South Carolina. I own a New Holland 1925, 4x4 with Hydrostatic transmission which I purchased new from a local dealer no longer in business. Originally equipped with a Bush Hog 2245 QT frontend loader (still have it) and also with a backhoe attached to the 3pt hitch. I...

Hello All, I need some help. I have a NH 1925. With a 9x3 Trans. I replaced the clutch 2 years ago and all worked fine. The other day I was spreading some rocks put the tractor in reverse went about 2 feet and it just quit moving the pto does not work. I can shift into any gear with no grinding...

Unbelievably, NH doesn't offer the polished rod in the steering cylinder by itself. You have to buy the entire steering cylinder for a smooth $400. I can't believe there's not an alternative (e.g. straighten the polished rod?). Anyone had any experience with this? Anyone know a cheap place...

Last cold day, my NH 1925 started up, ran 10 seconds and died. It almost started on second and third tries. I turned off the fuel AT the bowl, that filter was so full of junk it had collapsed on itself, pulled loose from the bottom metal on one side, When I replaced the little filter, I failed...

A buddy at work has downsized and is wanting to sell his 1997 NH 1925. Good condition, runs like a top, has a factory loader, new seat, 13XX hrs and a Kioti 72" rear discharge finish mower ( I have the same RFM and really like it...cuts better than my Deere finish mower and is very heavy). I...

Hi folks, I've been pricing out Kubota l3700s, but I saw an ad today for a 1998/99 NH 1925 with 1900 hours. No loader but has controls. The asking price is $6200. I put a call in to the local dealer to get a quote on adding a loader but won't hear back until tomorrow. There don't seem to...

Hi. My first post and need help. Came across this site and have bean reading for long time. NH 1925 MFWD front axle final reduction gear oil leak. My question is can i press the first bearing and gear together off or just the bearing alone. Then gear take off C clip or snap ring then press last...

I am looking at either buying the 99 1925 with loader and aftermarket cab and turf tires for $16.500 or the 06 Kubota B7800 TLB with turfs for $24,000 They are both 4wd and the same dealer is selling both tractors . I am wondering which tractor would be better to get . If I got the 1925 I...

Hi all There is a New Holland 1925 for sale near me. It's got 1500 hours and it was new in 1999. I am hoping someone can direct me as to where to find some specs on it such as pto hp, hydraulic flow rate, rear 3ph lift, overall weight. Just basic stuff like that. TractorData does not list...

HAVE SHOT AT BUYING A 1925 WITH 7308 FEL AND BACKHOE/1900 HRS USED IN DIGGING FOUNDATIONS BY LOCAL CONTRACTOR/PRETTY GOOD SHAPE,HAVE BORROWED IT TWICE ALREADY AND WORKS GREAT/ $ $10,500 / I JUST HATE TO SPEND THAT MUCH MONEY AND POSSIBLY 18 MTHS 2YRS WILL BE FINISHED WITH NEED OF THAT TRACTOR/...

Three weeks ago I did some shredding at my place and parked the 1925 back in the barn, turned off the key and went home. Last weekend I went to fire it up and there was nothing - no glow plug light, no sound like it was trying to start, nothing. I thought that maybe I'd left the lights on or...

I borrowed a 1925 from a friend down the road the other day... needed to spread some SB2 (crushed stone) under a patio cover as a base for flagstone and my ROPS/canopy was too high to go under. I ran into a couple of issues. The position control on his tractor has only two positions: all the...

buynh-ML-653613-ML- Brand specific. Moved to NH Buying/Pricing forum.

As the time to build a house on my 35 acres is upon me, the need to buy a tractor (and learn to use it!) finally arrived. After keeping my eyes open for a year or so, I found a used package and bought it. While it's too late to go back now (and I've spent my first four hours with it and had a...

Does anyone have info on the horse power rating on new holland/ford 1925 model? looking at an add and is listed as 39hp, I thought it was less. was this tractor model just made 2 years? the only discussion Ive seen on this tractor was a battery problem. any other problems or is this a pretty...

Looking at NH 1925. How 'bout some user reviews? Longevity? Problems? Favorite implements? Thanks! My email address is ablaw86@alltel.net.

I am looking at A New Holland 1925 with 7308 loader and 1200 hours. Is $11,500 a reasonable price?

Need info on used tractor 1925 boomer - ready to make offer - help please. Is 1925 a true boomer or was this just before TC models. Is this similar to TC33? What are specs on tractor? Value of 1925 with, hydro 4wd, 55 hrs, r4 tires. Leaning toward orange before seeing this ad?