gearbox

My shear bolt broke and I'm trying to replace it but cannot find the hole to line up. The picture shows where the PTO shaft and gearbox connect . That looks like a grease nipple on the PTO U-joint . If it is there's no way to get a grease gun on it with that cylinder in the way did something...

I know it depends on models and this could very well be opinionated, but all around, who makes a better rotary cutter (brush hog), Bush Hog or Woods? I’ve never owned any Woods product but have owned many Bush Hog rotary cutters over the years and have been well-satisfied. It will be going on...

Hi !, this is my very 1st post !, I’m in Australia and have taken apart the gearbox to put new bearings in . The gears seem all ok , but there’s one shim which is 46mm od, is 1.5mm thick and 30mm Id I think it must go in next to or between bearings in end of case possibly . Maybe on the bottom...

Hey folks, Just sharing a recent project I tackled — I picked up a Valpadana 6045 RS with a completely busted gearbox and non-functioning hydraulics. Turned out the gear selector fork had snapped clean off, and the only way to get in was to split the case. I put together a custom jig using...

Question out there. Anybody know the best way to dismantle the gearbox assembly on a ft254? I’ve done the tractor split for the clutch a few years and it looks like again for a busted gear tooth just above the transfer case. To me it looks like six bolts just ahead of the transfer case on the...

Trying to find input shaft/gear (#700492) for old style Mott gearbox I know there is somebody out there with one sitting on a shelf covered in dust Help !!

I have a woods RC6 rotary cutter which I am in the process of servicing. I removed the plug located on the rear bottom of the gearbox and drained the oil. I then removed the top vent to fill it back up . At this point I checked the owners manual to find out how much oil to put in. It said to...

Hey everyone! I've not been here in a long time, but I'm looking for an online source to purchase a gearbox for my Mohawk 5 cutter. Suggestions? Thanks! hart547upY

Looking for a gearbox for a Frontier Dgm1072r. Old one has Woods stamped on side. Can anyone tell me if there is a Woods mower with the same gearbox?

Does anyone know where I can find a gearbox for a Farmtrac GMR 7A grooming mower?

I was able to buy a 4 basket KH500 for next to nothing, but it has a gearbox that has seen better days. There are two bearings on the input shaft, one is a sealed bearing about 2" in diameter and then a roller bearing that rides on the shaft farther back. The roller bearing is all egg shaped...

Last weekend I heard a metal clanking noise when I raised the deck on my F3060 while the PTO was engaged. I didn't think anything of it because I occasionally mow over some nasty stuff when I cut down areas outside my main yard and I end up with one of the blades 'ticking' part of my well worn...

Hi looking for gearbox parts for my MT23 need 5 gears in total from both pinion and main drive shaft. If anyone is breaking one of these or can point me in the right direction please contact. Many Thanks Matt

Has anyone replaced a 1:1.47 ratio brush hog gearbox with a higher ratio 1:1.93 or 1:2.83 ratio. Would this setup help the brush hog to operate under reduced acceleration contributing to fuel economy and more efficiency? Would the 1:2.83 ratio gearbox perform well using the ground speed PTO? The...

Is there a way to get the chain back on the reduction gear and drive gear without having to disassemble the entire thing? The gear's set screws, despite using Locktite, wiggle out and the gear comes loose then off comes the chain. It's very frustrating because it doesn't appear to be an easy...

Short story: I pulled the hydraulic cylinder case off of the differential gear case. When I turned the hydraulic cylinder case upside down, a small 1/4" bearing ball fell out. Any idea where this might have come from? Long story: Bought my first tractor, a used B7300 with 114 hours, from a...

I just bought an older ford rotary cutter. It is missing the top half of the gearbox and the pto shaft(I bought the thing for $60). The best I can tell the model number on the tag of the whole thing is 22-151. I’m having trouble finding the correct gearbox for it. The output shaft is 10 spline...

I reassembled my rck54 15bx gearbox, but the center shaft has movement. Is this normal or could something else be wrong? I replaced all the bearings. Reassembled everything and added oil. It was leaking from the oil seal. I have a new seal on order, but trying to see if I need to fix...

I purchased a used Rhino 10' brush hog last fall to use this year. I have broken the output shaft clean in to. There appears to be no rust on the shaft where it broke, but there are no stumps, just old rotten oak limbs out in the horse pasture. This is the second shaft I broke in two weeks...

Hi, can anyone tell me the following: Do I need to use the clutch with the use of an inverser? I have the forward and reverse handle on an Iseki GEAS TG333, which I believe is called an 'inverser'. (if not correct me please) In first and second group in all gears I can just switch from forward...

Hi, I was getting my new to me Rhino SE8 ready for some last of the season mowing. I was trying to check the oil level in gearboxes. I found that the 1/8" square headed pipe plugs for level drain in really good condition for a 20 year old machine. I was able to get 2 of the 3 off, but the third...

Hi all! I bought case ih 895 xl few weeks ago and I have a problem. Everytime when I stop engine, the tractor starts rolling like without engaged gear. The gearbox is equipped with hydraulic F/R shift. Hydraulic fluid is just between min and max and there is not a problem with driving whilst...

Hi everyone. recently purchased a Titan implements flail mower. Dealer says to put high temp grease in the gearbox instead of the n46 hydraulic and gear oil as the manual says. Anyone have any experience to share by doing this? He states that this is how they service all of their gearboxes.

complete newb here purchased a tractor a couple of years ago. It came with a rollins 5' rotary cutter. I have consistently maintained the oil level in the gear box. hit some stuff and the cutter is now vibrating like a big problem is about to develop. the blades are not striking the...