john

Tractor is luchring & jumpimg in f & r in all gears. Seems it would be impossible both potentiometets could go bad at one time

I need help figuring out what to buy! Please tell me what YOU would do! And how YOU would approach this project. We just bought a 150 acre farm (all crop land). All of it is rolling hills - nothing terribly steep, but not flat either. In the next year or so, I need to: 1. Cut and grade an...

Hello, while changing the battery on my F525, I accidentally dropped the handle of my socket wrench while it was attached to the ground and of course it fell on my hot terminal and started sparking (this was on my new battery). It took me a few seconds to grab a piece wood and knock it off...

Started up my JD 5055e drove it up to my shop to remove the 3ph to install the backhoe. Shut it off, removed the 3ph equipment and went to restart it. Nothing! I know about the cold start sensor at the front of the engine and that's been unplugged for years now. Thought the battery might be low...

2015 john deere 5085m keeps throwing code ECU 3673.07. It worked fine last fall, it’s been sitting pretty much all winter. Thanks in advance

John Deere 4300- I have this fluid leak in my left front tire area and was wondering what and where the fluid is coming from and how I can repair it. I am just guessing it is a seal gone bad in the front axle. Any thoughts will be appreciated. Posting a few photos to highlight the problem,

I was mowing with my D140 and on my way up the hill I got the deck stuck. I smelled burnt rubber and all the sudden it wouldn’t move. I assumed the belt slipped so I replaced it, however it still won’t move. It will move a little if I push it while my wife pushes the pedal, but then it stops...

The tractor will only go 14 mph in high rang and when I try to use the cruise control I get a 5 error code on dash

2007 F250 headlights were getting foggy and the light was not very good either. The plastic chrome was peeling off the grill too. I peeled the rest of the chrome off, sanded and painted the grill. I updated the headlights with modern looking LED driving lights integrated into the headlight case...

Anybody looking for a MX10 in the SouthEast ? It’s listed over in the marketplace. North Georgia Cutter is SOLD

I bought this 3pt hitch lift type MX10 cutter brand new. Used very little. Low hours. Approximately 2200lbs going off memory ? Works great. Always kept inside out of sun & weather. I went up to batwing & zero mower. $8900 pick up in North Georgia No trades Call Mike six78 98six...

Good evening everyone, new guy here. I recently bought a JD 2350 with a 245 loader. It has a quick-attach bucket, but not like the hook and pin QA I am used to. Mine has two square vertical spring loaded pins that lock the bucket in place. Attachments for this style seem pretty hard to find, and...

I recently purchased an 850 with factory dual remotes. I'm a large person and the levers hit my leg. Additionally, both valve bodies are leaking. I want to delete the remotes completely. I only run a mower and have other machines with loader. I've found the replacement "cap" that has no ports...

I am trying to determine the proper rear ballast for my 5055E. I have a 520M loader that has a max lift of over 3k lbs. I want to lift at least a ton and trying to determine rear ballast. The manual for the loader shows two options for a cab tractor and one option for OOS. I have an OOS. The...

I was stationed overseas for 4 years, meanwhile a handy man hired to maintain my property back in the states, blew the engine in my JD 4610. When I returned home I found it completely disassembled and I'm trying to put it all back together. There are a few points I'm stuck on, as I can't...

Started well run like crazy than died tried restarting with a little gas in the air breather started well than tried a little diesel in the air breather and bum an explosion what damage could it have caused .

Stated it and it run like crazy for 3 min than died

Hi, just joined and first post. I have a 25 acre property, some steep slopes and mostly forested. I'm wanting to buy a new smallish tractor with 4 in 1 bucket to do the following: Moving rocks and soil Pulling cut down trees out for firewood and lifting them into stacks Grading/maintaining...

Good running John Deere 70 Tractor with wide front end. No hour meter, so hours are unknown I have video of it running, if interested

Ive been reading here and on the internet that some owners turn up their hydraulic pressure on their 2520s been thinking about doing that any of you owners had done this? I check mine and its 2475psi thinking about going to 2700 will I break something or blow seals out with 200 more psi thanks

Does anybody know how much a complete set of 19.5-24 & 12.5/80-18 New R4 tires & wheels would cost from JD ?

I'm looking for comments and thoughts for the John Deere Frontier RB2284 Rear Blade. I have a 72" Land Pride and I'm thinking of going to a wider and heavier blade. This is much heavier than my current blade and I don't have rear hydraulics. Is this too heavy to adjust without hydraulics? My...

Anyone have any idea when this was built and what it is worth? I know in most case with serial numbers 001 would be the first one built? The story is it was bought new with this 1953 John Deere 40.

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

I have a 1986 John Deere 650 tractor. it is currently stuck in 4x4, the shifting handle just free wheels like its not hooked to anything. the roll pin in the handle is good. Can I pull the shaft that the handle is mounted on? I am assuming that the shaft it broken or what ever it was driving...

Hello All, I have recently bought a 1966 John Deere 4020, got a screaming deal on it. I am hoping to find a loader for it. I have seen that John Deere Loaders 48/148/158 do fit and work. I was able to find a few 'fairly local' but the asking price is higher than I paid for the tractor. I am...

I started a rebuild on my little 850. Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the middle cylinder...

Bought a 301A over a year ago that had been setting along time turns out all I needed to get it started was a new fuel transfer pump and rebuild the starter ….... everything seemed to work well except the rear lift arms wouldn't hold a middle position no biggie ran for a bit but I noticed was...

I just recently bought a John Deere 850 for a super cheap price compared to what the market is in my area. Everything seems to work as it should and it seems pretty clean. The only issue I’m having with it is it seems to have a slight miss to it around 2,000rpm not sure what it could be I’m...

I purchased a 5520, the instrument cluster is not working. I sent it to be tested and it works fine. I've had a mechanic work on it extensively with no success. The cluster has rpm, fuel gauge and temperature gauge. I'm considering just adding aftermarket fuel and temperature gauges. I'd love...

so she cranks but wont fire! I found she isn't getting fuel because after some testing without luck I finally decided to put gasoline on a rag and cover the intake with it and she fired right up. This tells me it is getting everything but fuel. I noticed I wasn't hearing the click as usual from...