kubota l2350

Finally got the parts to put my 4wheel drive shaft back in, the only real difficult part was getting the press pin out of the front wheel dive case, this pin keeps the cover for the shaft in. After that it was a pretty easy repair.

I bought a Kubota L2350 but I can't get it to go into 4wheel , the lever works goes up and down but I don't think it's in 4wheel. Any help appreciated

Cranking procedure for Kubota L2350

I'm adding a aftermarket loader to a kubota l2350 the loader vavle has three lines. On the parts breakdown the return goes to the rearend/tank. But the other go to a block on the rearend ontop the pump pressuree feed. My tractor has power steering with a priority vavle. My concern is since the...

Priced at 4,500. Listing does not have the hours, stated it was only used to mow lawn and it looks like that's probably true. Thoughts on this one?

On my Kubota L2350DT tractor, my tach keeps pegging out. At very low RPM, the tach seems to be correct, but as soon as I increase speed to run the backhoe, the tach pegs out. Does anyone have an idea what the problem is and a repair?:confused:

My L2350 will not turn over.

I have an L2350 Kubota tractor that I've owned for about 7 years. A bit of important back-story: Recently I replaced the battery. The new battery was the proper number of Amp-hours (actually more than the battery it replaced). I also made sure to get one that hadn't been sitting on the shelf...

Afternoon y'all! I've been using a Kubota L2350 for light farming work for several years now, great machine barely had any problems at all until recently. I've got a hydraulic oil leak coming out right under the steering wheel, my local dealer said it should be pretty easy fix and sold me...

Just bought a used Kubota L2350 and it needs new rear tires. My soil is sand and heavy clay. No serious AG work. Mostly using it for general chores, shredding and maybe some small food plot work. I have a LOT of wesatche and mesquite with some serious thorns. R1's can make terrible ruts. I am...

Hi, names Rob111, I have a 20 year old give or take L2350 with bucket that the 4 wheel drive went out on. still runs on rear wheels so I'm guessing it front. Anyone know of known problems I should look for first? Thanks

RH Hood. Front Grill. Grab handle. Seat. Seat spring. Thanks for looking! Evan

Got a L2350 (1996 year) see many people adding temp sender. They even show photos of the sending unit installed in the head plug, but no one say what part number they used that will fit on the L2350dt have picked up two units to date both did not fit the head plug. I am sure this head is on...

I have got a 1999 873 Bobcat and am about done using it (clearing ground, moving dirt, gravel, brush, etc). I bought it to do these chores and then going to sell it. Well, I have a gentleman wanting to trade me a nice Kubota L2350/with loader for my Bobcat. My question is about the tractor...

Hey guys/gals, new member and (obviously) first time poster. Have followed the forum for a while, but just now ready to pull the trigger on a tractor. Can't afford new right now, so going the used route. I own 40 acres, only 10 of which needs upkeep. Very flat property...was agriculture in the...

I have a BushHog 1846 qt loader, I have the opportunity to buy l2350 4wd at a reasonable price, will this loader work on this tractor, it was on a Yanmar YM1500 2wd. is there any where on the net that tells what all this loader will fit.

where do the support arms mount? I just acquired this tractor and it has a few problems! first I need to remove the LB400 loader, the 2 bolts in front have been removed, as well as the lower bolt on each side or rear tower. Problem control valve for bucket dump not responding, cant tip bucket...

I am looking for a good quality shop manual for my Kubota L2350DT. I have the original Operator's Manual and have saved it as a pdf file. I also have a parts manual saved as pdf and have purchased a pdf shop manual . The problem I have is all of the pictures and diagrams are very dark and are...

I want to add a front end loader (bucket) to my L2350 4x4 but have no idea where to even begin or how much it would cost. Of course I'd like to find a good used one but those seem hard to come by. Being that the L2350 is smaller than most tractors it seems to be a tough find. Any ideas on cost...

I would like to use this small tractor to build fence, maintain a 1200' gravel driveway, develop a Farmer's Market garden, and make some horse trails through south Texas mesquite. I expect to add a post hole digger at time of purchase and a box blade and shredder down the road...

Hello I"m new there so i Hope this is in the right spot ... what i got is my L2350 kabota ..when the temp drop's bellow 0 the front wheel's seem to freeze up?? it does it 2wd or 4wd it's like there's water getting in somewhere to freeze up the front driver shaft..which run's though the oil...

Ive been worling on this L2350 kubota for some time. It had hard starting probelms so i replaced injection pump, injection nozzles,glow pugs. Bleed in pump lines and now it spins over but wont start, Not sure what i did wrong?

I'm trying to replace the original loader valve on the L2350 with the "Brand" (Brand is Manufacturer name) valve available from Motion Industries. The configuration will work with the float in the right position etc. etc.. But I'm confused on the hose configuration. The Kubota valve (which...

Can't figure out how to get fel off machine. There are two arms available to hold up rear arms of fel, but can't figure out how they attach. And can I use the front bucket in a little down position like kioti removal?

Just joined up to see if useful information might be available at this site.

First post here. Been reading here for awhile but finally bought my first tractor. I bought a 1997 Kubota L2350DT 4x4 with a FEL. It has about 800 hours on it. I'm planning to go through it end to end to completely service it. Once it's completely serviced, I plan to repair the sheet...

Just purchased a Kubota L2350 and trying to learn everything I can about it. Scott

My Kubota L2350 lost all power steering @500 hrs. Turned it back and forth while going slow and regained some power. Tried turning all the way both ways to bleed any air and shutting off as per service manual. No better. Seemed as though power steering was getting no hydraulics at all so I...

Today, I purchased a CountyLine 3-point hitch log splitter from Tractor Supply (made by SpeeCo). The splitter utilizes the hydraulic system of the tractor. The problem is, the manual and instructions have zero about specifically setting it up to your tractor. I have done some research and it...

Today, I purchased a CountyLine 3-point hitch log splitter from Tractor Supply (made by SpeeCo). The splitter utilizes the hydraulic system of the tractor. The problem is, the manual and instructions have zero about specifically setting it up to your tractor. I have done some research and it...

Today, I purchased a CountyLine 3-point hitch log splitter from Tractor Supply (made by SpeeCo). The splitter utilizes the hydraulic system of the tractor. The problem is, the manual and instructions have zero about specifically setting it up to your tractor. I have done some research and it...

Hello, just became member, trying to research solutions to problems I'm trying to resolve on a very abused Kubota tractor. I'm 68 years old, live in rural south central Missouri and have 11 acres. Was raising Boer goats with donkey as a guardian. Due to health reasons sold goats and donkey. Have...

I think I've narrowed my no start problem down to the starter. When I remove the starter and hook it up to battery charger on the bench, the solenoid will kick in with a 10 Amp source but the starter doesn't turn. If I kick up the source to 50 Amps, the solenoid kicks in and the starter turns...

My L2350 PTO lever is difficult to engage. Any suggestions?

Does any one know if you have to replace both the hour meter and cable at the same time? My RPM gauge has started to act strangely and I believe that I need to replace it

I just bought a used Kubota L2350 which needs a few things fixxed. I'm wondering if you guys can recommend a good source for a parts and service manual? I looked around the net already and found anything from what appears to be dealer shop manuals for over $150 to someone selling that same thing...

So I have resorted to researching this for myself after numerous dealers couldn't help us. We purchased an L2350 (1997) and a Danuser F7 auger with down pressure attachment a couple weeks ago with the thought that we could have a set of rear hydraulics installed. Well, turns out getting rear...

Can anyone tell me the correct model number for a loader that fits an L2350 Kubota? Thanks in advance.

Greetings. Somewhat of a newbie here, while I am on my second kubota, I am not terribly mechanically inclined, usually relying on others to do my equipment repairs and maintenance for me. I currently have a third-hand L2350 just shy of 900 hours. I have had it serviced a couple of times over the...

I was using my 5' tiller yesterday and the transmission got very hot. How should it get when operating at 540 PTO speed on a 90F day? Thanks.

New in here and hoping for a little help. bought an L2350 used and ran it for awhile, and i need to put a clutch in it. Never put one in a tractor but dont really see the problem. Was hoping someone could just get me started so to speak, any tips you know. Also am looking for a repair or...

hello, I need to know where I can purchase a muffler and exhaust pipe for a Kubota L2350 tractor. thank you

We are buying a home on 10 acres with some fairly steep hills. The current owner has used a '95 Kubota L2350DT for last several years, has 1400 hours on it. He has asked if we want to buy it. It includes: Kubota L450S loader and bucket / Pacific DX60 Rotary mower / John Deere Roto tiller...

HAD A L2350 (about 1995 vintage) crack through the front end of the transmission - the dry part where the clutch/pressure plate lurks. A 4 whl drive with a front bucket. The bucket framework had dropped 2 support or connecting bolts underneath contributing to the problem. Gotta crawl under...

Ok... this is my first posting so hopefully i can get some help.. I have a Kubota L2350DT that has some major issues. First of all, I had problems with it starting, Rebuilt the starter to find out that it wasn't the problem. I was frustrated and so I wired the started in a way that could jump...

The manual says it will do a 72" which actually suprised me I thought even a 60" might be the max. My new place is a overgrown field so i don't want to push the little tractors limits, does a 60"er seam right?

Have a question on my L2350. The clutch disengages the tractor, but it is difficult to change the gear selector ( like it is torqueing up). Never have had any issues, 433 hours on tractor. Sits for long periods of time. What would cause this?

Considering a 1997 Kubota L2350DT, 425 hours. Curious to the reputation and/or concerns of this model. Is it considered a CUT or SCUT? Thanks

Looking at a 1997 Kubota L2350DT with a Woods/Dual 155 Front End Loader. From my other post, I've been looking at current models so am curious to know what the L2350DT now compares to in the Kubota (B series?) and Deere (2350?) lines. Thanks

I have found a 1997 Kubota 2wd L2350 with turf tires and 1600 hours. Cosmetically, the paint is somewhat faded, but the body work looks very straight. The pictures show a tractor that is probably in "good" condition. No equipment is included. Does $3000 sound about right for this tractor...

Is this tractor worth $8,500.00 there is not supposed to be anything wrong with the tractor this is from a dealer...any and all opinions welcome TIA

Does anyone know the minimum collapsed and maximum extended lengths of the telescoping stabilizers on a B2910? I have searched the site and found information on adding these to a B7610 w/ parts from B2910. Thanks in advance. Brian.

Am I asking for trouble? Can this tractor handle a 5' tiller. I have very sandy soil and can take my time. Thanks for input.

Working with a friend last weekend and using his L2350. Hooked it up to a 3 point bale spear and tried to pick up a bale. Bale measured 4' by 5' diameter. 3 point would not get it off the ground. It seem to go into bypass mode and moved the bale up a little, but not off the ground. It did...

Told a friend about adding a remote to my Massey 135 and he asked if it could done to his L2350 4 wheel drive with FEL. He wants to use it to pull a rake for haying since that would not require much in the way of HP. However, the rake requires one remote to unfold the 8 wheels. The rake is an...

Where is a good place to buy ag tires for my tractor? Has anyone put R4s on this tractor? What size would they need to be? I assume the rims will be replaced. Thanks.

Where can I find a decent top link. I tried my Kubota dealer and it was nearly $200. I think this is too much, and will likely buy aftermarket. I don't know what length that I need. Thanks--all help is much appreciated. Brian.

It's time to buy a boxblade for my next round of projects, virgin gravel driveway,trail grooming,leveling. L2350 is 25hp, 21pto hp. is a 5' too much?. I have turfs w/chains 2-ladder, footprint is approx. 58". I just don't know if I can pull a 5' footer w/o getting hung-up. I know the different...

I had trouble getting my tractor to indicate a fluid level using the sight glass on the side of the transmission housing. The fluid is 1" from the top and still not showing in the sight glass. Any ideas? Thanks. Brian.

Late 80's model L2350: Will fire and sputter, but wont stay running. I cracked the fuel filter and got flow out of it. (I will pick up a new one this week). What else could it be?

I purchased sets of 7-16 and 9.5-24 ag on wheels to change the 13.6-16 and 24x8.50-14 turf on my L2350. The center hole and lug holes match on fronts (7-16) They are 6 on 6" with 4.5" center hole. The 9.5-24 have 8 on 8" lugs with 6" center hole (should be 6 on 6.5" with 5.25" center hole) I...

Has anyone put R4's on a l2350? Thanks.

I need to replace one of the cylinders that performs the bucket curl and I got a price from the dealer of $325 this morning. Is there a cheaper source of replacement cylinders? Thanks.

How can I tell my transmission is filled? I removed the fill cover and can't see the level. Thanks. Brian.

I have a Kubota L2350 DT (4x4) with power steering. I was pushing through some heavy brush and noticed oil coming from under the steering wheel and running down the steering column. Steering still functions normally. Any suggestions would be appreciated, Okie

Question: The manual for my tractor says it can accomodate a 72" rotary cutter. But it only has 20.5 pto hp. It DOES run my bush hog finishing mower 5' quite well. Should i buy a 4 footer or a 5 footer? and what brand would you recommend for value w/out breaking the bank. Should i go 4 foot...

front wheels not powered when in 4 wheel drive. does any one have brake down of gear box infront of transmission or know what i will find when o take this apart thanks tuttle

L2350 can not find place to check oil in rear end of tractor. can any help? thanks

I recently purchased a kubota L2350 with a LB400 loader. The loader works fine but the tractor does not have power steering or 4WD. I have a L2050 that has ps and 4WD. The frame and bolt holes all look the same on both tractors. (First question) After I swap FEL and hydraulic lines, Will the FEL...

I need to replace both fenders , need source for used, salvage or aftermarket. Thanks. Dan

Hi folks-I'm looking at an L2350 w/580 hours with a front-loader, backhoe, brushhog and post hole digger for $10,500. Is this a good deal? Also, looking at a B7100HD with front-loader, brush hog and roto-tiller for $5500.00. Good price? With the front-loader and its frame on the B7100 how much...

L2350 gear-trans....Whoops. I thought I did all the maint. ,but missed one. The manual states there is a grease fitting on the clutch release ?. There is a steel cover on the right side of the trans/clutch hsg. Remove it and grease the fitting. Huh!. I removed it but don't see any fitting. The...

Hey guys, a newbie to the board here. I'm looking at a 1992 L2350 with 1200 hours. 84Q loader and manual 8/2 trans. Price is $6,500 seems to be in average condition for use and years...Thanks for the feedback.

We have a l2350 which has worked real well for us. Tractordata.com shows this model as having live pto, but from what I can tell on ours, it doesn't. When I let the clutch out with the pto engaged and the tractor in gear, the pto engages at the same time as the tractor starts moving. Is...

I don't want to step over the line here but in my playing on the web I found a L2350 w/ some toys for sale in central Texas for $7500. The website is http://www.jackmauldin.com/equipment_for_sale.htm Just thought I would let you 'Bota folks know about it.

This is my first post and first potential tractor purchase. I need a bit of help deciding on which tractor to pick. First I'll give you a bit of info about me... My wife and I just bought a small 8 acre Farm. It is mostly flat with a couple acres of horse pasture, about 4 acres is currently...

I am interested in looking at a used Kubota L2350 w/ 28hp, but I have a few questions for anyone who may be able to help. This my first experience with tractors so please bear with me. First, is it necessary to have power steering to attach a front-end loader? I was told by a local dealer...

Howdy. I have just started using a brush hog with my L2350 and I noticed a clicking noise when the PTO is winding down. It doesnt happen under power. If I turn the shaft with the pto engaged (engine off) you can definately feel it. Is this normal? Shaft is tight and the tractor is still...

Have a L2350DT with Woods 59 mower. Lift arms will not go all the way down. I rebuilt the control valve with "O" rings. It worked for a day. Now the mower is about 6" to 8" from from ground. Anybody have any suggestions? Thanks

Hi - I presently have a Kubota L2350 with bucket loader, bush hog and 72" Woods finish mower. I have about 60 acres and am feeling way underpowered especially in the bush hog area where the max size I can have is 5' with this tractor and that bogs down considerably in the heavy stuff. Having...

I've been offered a Great Bend 220 loader for my L2350 tractor, but can't find anything about it. No answer from GB so far. Does anyone know if this is a good fit and what sort of bracketry may be required to do the installation?? Thanks, Wilson

Can anyone give me advice on the reputation and loader work performance on the Kubota L2350 and or the New Holland 1720 tractors. Is 1100 hours 1996 asking for trouble as I fear?I am getting opposite opinions from dealers that actually carry both lines despiet the larger HP of the 1720 @ 27 HP...

I just bought a lightly used L2350 with 500 hours to replace my B7100. I have put a couple hours on it and am very pleased with the purchase so far. I mowed a couple acres with my 60" Bush Hog finish mower and it did a great job, no straining in the taller grass or going up slopes. And it...

I am considering a L2350, 500 hours 4wd with loader that is for sale locally, the asking price is $9500. It is supposed to be in excellent shape, but I haven't had time to go look at it yet. Any comments? The price seems reasonable to me. Does this tractor have live pto ? Thanks!

Hi, My wife and I just bought a 5 acre tract of land which we will be building on. We are in need of a sub-compact to perform clearing of field land (no tree removal) and light grading (after the excavators have done their work). I will also be using for maintenance. The land is elevated...

I have the opportunity to buy a 1996 L2350 with 484 hours. It is 4x4, not HST, and includes a Woods 155 FEL and Woods 7500 BH. Owner says a tree fell across the bucket causing some minor dents and front body damage. Not the cleanest looking machine but it started right up. Owner will throw...

Mine is missing one. Looking for a replacement if anyone has one or ideas where I might find one (salvage???) Thanks. Mark: 610-827-1386 / email: A6Aviator@msn.com

Can anyone provide some help / infor to me regarding my recently purchased used L2350? Problem is: intermittent starting. I'm in Pennsylvania and it's below freezing out. Started fine day before yesterday. All I get now is a "click". Could it be temperature related? Battery is relatively...

I'm curious why I don't see more discussion on L 2350. I am considering one for my new 10 acres. 1995 mdl with la450 loader. 640 hours in excellent shape. I hav'nt purchase before so I don't know what attachments I would really appreciate. (Will be developing hobby farm and building house.)...

This auction might jelp someone determine what a spare set of tires/wheels is worth. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=1920110442

have a 'bota L2350 Diesel 4x4, with 650 hrs, turf tires and loader, runs, new front axle, average condition....just wanted idea of price range if i sold it

I've been using an L2350 for some time. Looking at Kubota's web site has all new model numbers. What model is equivalent to the L2350?

just got back from an auction in west central ohio where a very clean L2350 with LB400 FEL (no mower) sold for 10900. it looked like new, had only 230 hours. was owned by an 83 year old man who had bought it new. his 5 foot tiller attachment sold separately for 900. 12-7-01

I am looking to buy a L2350 2WD with no attachments. Do any of you guys know anything about them and how much do you think it is worth with 200 hrs and in good condition? Thanks.....Jon S.

I found a used L2350 with LA450S front end loader, York rake, box blade, 51 hours, excellent asking price is 12,000. wadda yall think?? How does it compare to the B2710 except for HST?

I found a used L2350 with LA450S front end loader, York rake, box blade, 51 hours, excellent asking price is 12,000. wadda yall think?? How does it compare to the B2710 except for HST?

Could someone give me info on the L2350 (H.P., Years made,anything appreciated)