kubota m7030

My fuel gauge works part of the time. Right now it is stuck on 1/2 tank. How much of a job to replace or repair? Or do I stick with the stick?

My loader works off one set of remotes. So, when using the loader, I have to lock the remote lever back and, in that position, the 3-point hitch and the other remote doesn't work. I have been living with it but wish I could run the loader and the 3-point at the same time. This was discussed...

The 7030 is a Fiat tractor with Kubota parts. The left front hub is leaking (oil spot on floor) I checked the oil level by removing the fill plug, it's over full. On the top of the unit there is a zerk fitting and my Shop Manual and owners manual says nothing about greasing it. Shop Manual...

I have had this tractor for a year and it is temperamental to start. But, I have found that if I lower the rpm to 500 before shutting off, it will start instantly with no problem. But, yesterday, I started the tractor, backed it out of the shed, let it run for a minute and reduced the rpm's to...

Where do I get a Service Manual for my M7030? manualslib does not list the 7030. The Owners Manual I got on e-bay, I don't' believe is a copy of the factory manual.

I have found a small parasitic drain (short), so I looked at the fuse block and found a zip tie holding it together. Eureka moment! I'll bet that's where my drain (short) is. Off to the Kubota dealer to see if I can look at a parts picture and schematic to see what it is supposed to look...

This tractor has <4000 hrs and I have not looked at it yet. I believe it has a 16 speed trans/ 4 reverse and no shuttle, it is beast to load with? Looking for somebody with experience with this tractor. What are the weak spots?

Haven't looked at either tractor yet. Kubota is older and has <4000 hrs, the Mahindra has <1000 hrs and is more money. Both have loaders. Tractor will be used about 300 hrs per year for mowing and light tillage. (3 bottom 14 inch plows) I like the 16 speed trans, but not sure it has a...

Does anyone know where I can find stabilizer bars for the 3 point hitch to replace the chains that are on it? Thanks Dave

I just bought myself a M7030 with a M540 Loader. Just looking for some specs on the loader, breakout force, lift capacity etc. Right now it has a big 6' bucket on it. I am starting my search for a bale spear and maybe a set of forks for the loader. I do not know what style of quick attach...

I was at a new customer's place replacing the o-rings on the governor shafts in the injection pump on his Ford 445C and a couple other little things. When I was wrapping up he lead me over to his M7030 in a tentative kind of way. I told him that now we were getting into my wheelhouse. He seemed...

My Kubota M 7030 has a Hydraulic problem with the three point hitch,It will not work.....It did work, but now it will not!...Is the system open or closed?,Is there any switch lever etc. that may have been turned that will prevent the 3 point from working? Seeking answers to fix the...

I have an M7030 that has been trouble for a while...It has been used little except in fall of year,,,mainly since I got it because of oil blow-by out of blow-by tube...Year before last when the problem started it would start blowing oil out only after it got hot (not really hot but I mean when...

My boy Mike leaned on the tractor fender while driving and it fell off! The bolts and threads are completely rusted out, way too far gone to install a larger diameter bolt. Any suggestions on how to approach this?

Looking at a 1990 m7030 2wd 3000 hrs. Supposed to be 68 pto. Are they a good tractor, are they quiet (havn't seen in person), are they efficient? Is it worth $7000 or not? General mpressions. I see they were made all the way to 1998.

I bought an m7030 about one month ago. This is my first tractor and so far its done what I want and more. Why are there so few m7030s around? Its 71hp and a real strong tractor. Cat 2. Another question. I seem to break hold pins on the bush hog. I have a cat one bush hog and cat 2 tractor so i...

I have a 94 m7030. I dont see much about them but its a nice tractor for my first one. Primary used for bush hogging and box blade stuff. My question is: When i engage the pto cluth I notice a bit of what I call grind, sort of like change gears on the tractor when not stopped. PTo works fine...