lever

There are two empty slots on my ~2019 CK3510 between the 3 point raise/lower lever and the cup holder. Assuming these are for addons, anyone know what those would be for? I didn't see anything in the workshop manual but its also like 400 pages.

Hey Guys, My issue with my Kioti CK30 is pretty much explained in the title. I've removed the self-centering device along with the spring-loaded doohickey next to it which helps a bit but definitely not the issue. The foot lever rotates two shafts extruding from the trans. The rear shaft seems...

L3600, glide shift(I think) shift lever froze. Temps were in the low 20's, shifter just would not move. Forward and reverse were fine, I was just in 2nd gear, very slow. Running the tractor did not unfreeze it. Parked in the shop, turned the heat on, and it unfroze in about an hr, but as soon as...

my lift lever has loosened up and will no longer stay back. My understanding is that i should try to tighten the nut on the end of the shaft and if that doesn't work then the friction washers need replacement. On the GTT forum a poster was saying i need to remove the wheel and fender- does...

The brake lever wants to stay up all the time, which causes the beeping noise. Does anyone know if the spring is needed and if not, is it removable? If it could be removed, the lever would stay in the lower position as it should.

2018 MX5200 with 400 hrs. The rear 3pt raise/lower lever is ridiculously hard to operate. Seems to be getting worse. Makes small adjustment and smooth operation difficult. What am I missing? Thanks in advance

I've owned my 336D for about 4 months now, most of that time was spent fixing various issues. The tractor didn't have a parking brake lever on it, I found a used one online, thinking that I was just getting the lever, and that I'd have to brain out how it mounted, as the parts diagram is...

My tractors 3 point lever is labeled 0 - 10… with 10 being fully raised… Problem is, between 0 and 7 nothing happens out back… so 7 thru 10 is the range that raises/lowers the implements… rather abruptly… I’ve watched the lift arms without anything attached… nothing happens… so it’s not the...

It is time for a good grease gun for my tractors and implements. Does anyone have thoughts on the LockNLube Easy-Prime Lever Grease Gun? Is it worth the ~$90 or so it costs these days? Or, is there something better or similar for less money worth considering? I have a $30 Almetite today...

I was spraying today. I finished about the 4th row, turned right to turn around and hit the next row, and the 3pt pto pump tether popped off as I was turning and hit a rut that jarred the tractor back and forth (obviously needed a little more slack in the tether). I pulled the lever up to...

Hello, Ive just brought a Yanmar F210 Forte. There is a lever on the Footplate, RHS, yellow cap on end of lever (lever next to lower RH leg), this lever is next to Diff Lock pedal. This lever slides up and down in a range of approx 10cm. It operates a linkage that is mounted on the RHS of the...

Reaching the range shifter on our M59 has been a bit awkward and required a more arm and shoulder effort than is comfortable. So I finally got around to improving it for a better personal fit. Here is a simple modification that has worked well. rScotty

Have TYM 554 and lift arms will not raise the brush cutter. Attempted to move the draft lever but it will not move. How do I free the lever up.

I have a JD 790 with bucket 70. 2007 model. My question is the arm release supposed to have a curl in it or be straight? One was damaged from trying to lift tree off trailer. The other arm has a curl. Which is correct?

The 3 point lever has been getting progressively harder to move over the years, now requiring dismounting from the tractor and pushing with two hands. I sprayed what I could reach with some PB Blaster lubricant, but even then I ended up bending the lever pushing too hard on it tonight. There...

Have a tc33 and the 3pt lever is seized. Any insight, have had the tractor for 20 years and never has happened?

Hello, I have a Belarus 250AS that I am trying to get running and have a problem with the decompression lever. It is hard to move. At the engine case, I have to pry the rod backwards to open the compression so the engine will 'free-wheel' as it should. I then have to push the lever forward with...

I just replaced the neutral safety switch. Hardest part of the job was getting the cover back on and everything aligned properly and keeping the darn gasket in place (and clean). I have the bolts snugged down and verified that the new switch works. The old one was intermittent, so hopefully...

Hey y'all, new here. Was hoping to find some help with my 5075E. Was out running it a couple days ago and it was shifting into all the gears and acting normal and then randomly one time I went to go back into 3rd from second (just going down the road, no implements running) and the shifter lever...

Is the left side lever between your knees on the floorboard only to be moved with the tractor turned off, or should the right lever in N allow that lever to be switched back and forth? Trying to decide if my tractor isn't acting right or that I'm the one that is messed up? I can't go from pto...

Does anyone have a suggestion on how to prevent the joint rod end from slipping out of the control lever on a LA463FL? I replaced it and it works for a brief time and then slips out, usually when lowering. I left the cover off and observed it and it even will slip out with the bucket lowered...

There’s a spot for lever on the right side of the 1st gen GC1700s that has no decal. Is that where the rumored power beyond kit lever was supposed to go?